2014 Hilux · Service Manual BODY ELECTRICAL

Microphone Circuit between Microphone and Navigation Receiver Assembly

Circuit diagnosis · Vehicles built from Aug 2013

DESCRIPTION

  1. The navigation receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
  2. Using this circuit, the navigation receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the navigation receiver assembly.

WIRING DIAGRAM

E278095E06

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
  1. Disconnect the N9 navigation receiver assembly connector.

  1. Disconnect the M6 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-4 (MACC) - M6-4 (MACC)
    Always
    Below 1 Ω
    N9-5 (MIN+) - M6-3 (MCO+)
    Always
    Below 1 Ω
    N9-19 (MIN-) - M6-2 (MCO-)
    Always
    Below 1 Ω
    N9-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    N9-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    N9-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    N9-18 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK NAVIGATION RECEIVER ASSEMBLY

  1. E284852E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-18 (SGND) - Body ground
    Always
    Below 1 Ω
    N9-19 (MIN-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N9-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

Text in Illustration 
*a
Component with harness connected
(Navigation Receiver Assembly)


NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


3. CHECK MAP LIGHT ASSEMBLY
E244515E05
  1. Turn the ignition switch to ACC.

  1. Connect an oscilloscope to terminals 3 (MCO+) and 2 (MCO-) of the map light assembly connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Result 
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly is output
    A
    A waveform synchronized with the voice input to the map light assembly is not output
    B
    Text in Illustration 
    *a
    Component with harness connected
    (Map Light Assembly)



B
Go to step 4
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. CHECK TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly with a new or normally functioning one (Click here).

  1. Check if the same problem occurs again.

    Result 
    Result
    Proceed to
    Malfunction disappears
    A
    Malfunction does not disappears
    B



B
Go to step 5
A

END (TELEPHONE MICROPHONE IS DEFECTIVE)

5. CHECK MAP LIGHT ASSEMBLY
  1. Replace the map light assembly with a new or normally functioning one (Click here).

  1. Check if the same problem occurs again.

    Result 
    Result
    Proceed to
    Malfunction disappears
    A
    Malfunction does not disappears
    B



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

END (MAP LIGHT ASSEMBLY IS DEFECTIVE)


← Reverse Signal Circuit (from Aug 2013)Display Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter (from Aug 2013) →