Microphone Circuit between Microphone and Radio Receiver
Circuit diagnosis · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
Microphone signal from the telephone microphone assembly is sent to the radio and display receiver assembly. Also, power is supplied from the radio and display receiver assembly to the telephone microphone assembly.WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for T-Connect.
| 1. CHECK TELEPHONE MICROPHONE ASSEMBLY (OPERATION CHECK) |
Enter the "Microphone Check" screen. [Refer to Microphone and Voice Recognition Check in Operation Check (Click here)]

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Push the recording switch and perform voice recording.
- HINT:
- Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
- Voice can be recorded for up to 5 seconds.
- Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
w/ Recording Function:Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.
- OK:
- All check results are normal.
|
|
||||
| OK | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY) |
Disconnect the R21 radio and display receiver assembly connector.
Disconnect the M6*1 or M8*2 map light assembly connector.
- *1: except Australia
- *2: for Australia
- *1: except Australia
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for Australia:
Tester Connection
Condition
Specified Condition
R21-4 (MACC) - M8-1 (MACC)
Always
Below 1 Ω
R21-5 (MIN+) - M8-2 (MCO+)
R21-19 (MIN-) - M8-4 (MCO-)
R21-6 (SNS2) - Body ground
R21-4 (MACC) - Body ground
Always
10 kΩ or higher
R21-5 (MIN+) - Body ground
R21-19 (MIN-) - Body ground
R21-18 (SGND) - Body ground
- except Australia:
Tester Connection
Condition
Specified Condition
R21-4 (MACC) - M6-4 (MACC)
Always
Below 1 Ω
R21-5 (MIN+) - M6-3 (MCO+)
R21-19 (MIN-) - M6-2 (MCO-)
R21-6 (SNS2) - Body ground
R21-4 (MACC) - Body ground
Always
10 kΩ or higher
R21-5 (MIN+) - Body ground
R21-19 (MIN-) - Body ground
R21-18 (SGND) - Body ground
|
|
||||
| OK | |
| 3. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
R21-18 (SGND) - Body ground
Always
Below 1 Ω
R21-19 (MIN-) - Body ground
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
R21-4 (MACC) - Body ground
Ignition switch ACC
4 to 6 V
| *a |
Component with harness connected (Radio and Display Receiver Assembly) |
|
|
||||
| OK | |
| 4. CHECK TELEPHONE MICROPHONE ASSEMBLY |
Replace the telephone microphone assembly with a known good one (Click here).
Check that the malfunction disappears.
- OK:
- Malfunction disappears.
|
|
||||
| OK | ||
| ||
