2014 Hilux · Service Manual BODY ELECTRICAL

Reverse Signal Circuit

Circuit diagnosis · Vehicles built from Aug 2013

DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission

WIRING DIAGRAM

E278684E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for T-Connect.


1. CHECK VEHICLE SIGNAL (OPERATION CHECK)

  1. E278094
    Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (Click here)].

  1. Check that the display changes between ON and OFF according to the shift lever position.

    OK 
    Shift Lever Position
    Display
    R
    ON
    Except R
    OFF

    HINT:
    This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
E140414E81
  1. Disconnect the radio and display receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R21-2 (REV) - Body ground
    Ignition switch ON, shift lever in R
    7.5 to 14 V
    R21-2 (REV) - Body ground
    Ignition switch ON, shift lever not in R
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Automatic Transmission)
    B
    NG (for Manual Transmission)
    C



B
Go to step 3

C
Go to step 5
A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Disconnect the R21 radio and display receiver assembly connector.

  1. Disconnect the N8 park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R21-2 (REV) - N8-1 (RL)
    Always
    Below 1 Ω
    R21-2 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

  1. E270424E12
    Disconnect the park/neutral position switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N8-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/neutral Position Switch Assembly)

HINT:
  1. for A340E: Click here
  2. for A340F: Click here
  3. for A343E: Click here
  4. for A343F: Click here
  5. for A750E: Click here
  6. for A750F: Click here



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the R21 radio and display receiver assembly connector.

  1. Disconnect the B1 back-up light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R21-2 (REV) - B1-1
    Always
    Below 1 Ω
    R21-2 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)

  1. E270423E03
    Disconnect the back-up light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-2 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Back-up Light Switch Assembly)
    Result 
    Result
    Proceed to
    OK (R150/R151/R156)
    A
    OK (R150F/R151F/R156F )
    B
    OK (G50)
    C
    NG
    D



B
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)

C
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)

D
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)


← Speed Signal Circuit (from Aug 2013)Microphone Circuit between Microphone and Radio Receiver (Jun 2011 – Jul 2012) →