Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P2A00  A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P2195).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) Calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2 trip detection logic).
·

Air fuel ratio sensor

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

After the engine is warmed up, the ECM performs air-fuel ratio feedback control to maintain the air-fuel ratio at the stoichiometric level. In addition, active A/F control is performed for approximately 10 seconds after the preconditions are met in order to measure the air fuel ratio sensor response rate. During active A/F control, the ECM forcibly increases and decreases the injection volume a certain amount based on the stoichiometric air-fuel ratio learned during normal air-fuel ratio control, and measures the air fuel ratio sensor response rate. The ECM receives a signal from the air fuel ratio sensor while performing active A/F control and uses it to calculate the air fuel ratio sensor response rate deterioration level.

If the air fuel ratio sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and stores the DTC.

A115363
4.26,1.469 4.104,1.146 false 4.521,1.75 4.74,1.125 false 0.104,0.052 2.49,0.375 2.385,0.323 12 false Air Fuel Ratio Sensor Output: 1,0.844 2.188,1.104 1.188,0.26 10 false Active A/F Control 0.365,1.76 2.302,2.063 1.938,0.302 10 false Air Fuel Ratio Sensor Output 3.635,1.063 4.198,1.313 0.563,0.25 10 false Normal 4.792,1.052 5.813,1.344 1.021,0.292 10 false Malfunctioning 4.083,0.177 5.865,0.469 1.781,0.292 10 false Approximately 10 Seconds 0.823,2.719 2.208,2.906 1.385,0.188 10 false Fuel Injection Volume 2.896,2.51 3.542,2.698 0.646,0.188 10 false Increase 2.896,2.917 3.542,3.104 0.646,0.188 10 false Decrease 4.833,0.76 5.385,0.969 0.552,0.208 10 false ON 2.719,0.594 3.094,0.781 0.375,0.188 10 false OFF

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Active A/F control Executing
Active A/F control performed when following conditions met -
Engine coolant temperature 75°C (167°F) or higher
Idle OFF
Engine speed 1000 to 4000 rpm
Air fuel ratio sensor status Activated
Engine load 10 to 50%
Transmission gear 2nd or higher
Catalyst monitor Not executed
Intake air amount 5 to 16 gm/s

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.


A301694
1.313,0.854 1.521,0.552 1.521,0.552 1.604,0.552 false 0.354,0.188 1.365,0.427 1.01,0.24 10 false Vehicle Speed 0.177,1.135 1.375,1.344 1.198,0.208 10 false 60 km/h (38 mph) 0.917,2.188 1.365,2.479 0.448,0.292 10 false Idling 0.188,2.427 1.385,2.635 1.198,0.208 10 false Ignition Switch off 2.021,2.115 2.469,2.406 0.448,0.292 10 false [A] 1.781,2.698 2.615,2.979 0.833,0.281 10 false Warming up 3,2.74 4.271,3 1.271,0.26 10 false 10 minutes or more 3.49,1.271 3.938,1.563 0.448,0.292 10 false [B] 4.385,3.146 4.833,3.438 0.448,0.292 10 false [C] 6.75,3.146 7.01,3.417 0.26,0.271 10 false [E] 5.521,2.75 6.792,3.01 1.271,0.26 10 false 10 minutes or more 6.031,0.906 6.479,1.198 0.448,0.292 10 false [D] 1.656,0.479 4.448,0.74 2.792,0.26 10 false Between 75 and 100 km/h (47 and 63 mph)

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the intelligent tester on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the intelligent tester on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (38 mph) for 10 minutes or more in a city area [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2A00.

13.

Check the DTC judgment result.

Intelligent tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the following procedure.



14.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


15.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P2A00.

19.

Check the DTC judgment result.

Intelligent tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

Sensor 1 refers to the sensor mounted in front of the Three-way Catalytic Converter (TWC) and located near the engine assembly.

·

DTC P2A00 may be stored when the air-fuel ratio is stuck at a rich or lean value.

·

A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read DTCs.

Result:
Result Proceed to
P2A00 is output A
P2A00 and other DTCs are output B


HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the intelligent tester on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

Powertrain > Engine > Active Test
Tester Display
Control the Injection Volume for A/F Sensor
50004 61 2

f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the intelligent tester.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Intelligent tester Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1
(Air fuel ratio)
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
O2S B1S2
(Heated oxygen)
-12.5% Lean Below 0.4 V

Result:
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to

Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.

Lean/Rich Lean/Rich Normal A
Lean Lean Actual air fuel ratio lean B
Rich Rich Actual air fuel ratio rich
Lean Lean/Rich Air fuel ratio sensor malfunction C
Rich Lean/Rich Air fuel ratio sensor malfunction



h.

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>DATA LIST / ACTIVE TEST



A

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)

B

4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

C

8.REPLACE AIR FUEL RATIO SENSOR
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P2A00.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2A00 is output) B




A

B

8.REPLACE AIR FUEL RATIO SENSOR
4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

5.CHECK AIR INDUCTION SYSTEM

NG

5.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system.


Result:
Proceed to
OK
NG



OK

6.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

6.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL INJECTOR ASSEMBLY

NG

12.INSPECT FUEL PUMP
7.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

8.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

8.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P2A00.


k.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL (DTC P2A00 is output) A
NORMAL (DTC is not output) B




A

10.REPLACE ECM

B

END

10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.PERFORM CONFIRMATION DRIVING PATTERN
11.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P2A00.


k.

Check that the DTC judgment result is NORMAL.


Result:
Result
NEXT



NEXT

END

12.INSPECT FUEL PUMP
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE FUEL LINE

NG