Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P20CF  Exhaust Aftertreatment Fuel Injector "A" Stuck Open  


DESCRIPTION

Refer to DTC P200C (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P200C).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20CF Exhaust Aftertreatment Fuel Injector "A" Stuck Open AF Lambda B1S1 is less than 0.85 for a certain time while the engine is running
(1 trip detection logic)
·

Open or short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

Fuel filter element sub-assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored

Related Data List
DTC No. Data List
P20CF/94 AF Lambda B1S1
Exhaust Temperature B1S2
Exhaust Temperature B1S3

CONFIRMATION DRIVING PATTERN

P20CF
DTC Detection Drive Pattern PM forced regeneration

MONITOR DESCRIPTION

The ECM monitors the air fuel ratio to detect whether the exhaust fuel addition injector assembly is stuck open.

If the air fuel ratio becomes too rich, the ECM determines that the exhaust fuel addition injector assembly is stuck open, illuminates the MIL and limits engine output.

A248903
2.969,1.615 2.573,2.354 2.573,2.354 2.49,2.354 false 0.177,0.167 1.688,0.469 1.51,0.302 10 false Malfunction Detection: 0.25,1.031 1.469,1.302 1.219,0.271 10 false AF Lambda B1S1 3.854,2.031 4.927,2.365 1.073,0.333 10 false MIL Goes On 1.885,2.271 2.615,2.51 0.729,0.24 10 false Abnormal 5.552,1.031 6.656,1.323 1.104,0.292 10 false Normal 5.75,1.49 6.938,1.74 1.188,0.25 10 false P20CF Threshold 1.792,0.604 2.219,0.875 0.427,0.271 10 false Lean 1.802,1.354 2.208,1.615 0.406,0.26 10 false Rich

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P20CF)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P20CF is output A
P20CF and other DTCs are output B


HINT:
·

When DTC P20CF and following DTCs are output, uncombusted fuel adhesion to the air fuel ratio sensor due to air fuel ratio sensor malfunction, fuel leaks, insufficient combustion due to parts malfunction (intake, exhaust or injection system), or an exhaust fuel addition injector assembly wiring malfunction is suspected as a cause. Therefore, diagnose the following DTCs first.

·

DTCs for the air fuel ratio sensor are P2237, P2238, P2239, P2252 and P2253.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P2237

·
·

DTCs for the exhaust fuel addition injector assembly wiring malfunction are P20CB, P20CD and P20CE.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P20CB

·

A DTC for EGR valve flow malfunction is P0400.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0400

·

A DTC for EGR valve stuck open is P042E.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P042E





A

2.CHECK FOR WHITE SMOKE (WHITE SMOKE AND ODOR)

B

7.GO TO DTC CHART
2.CHECK FOR WHITE SMOKE (WHITE SMOKE AND ODOR)
NOTICE:

If a fuel odor is noted from the white smoke during the inspection, fuel leaks from the exhaust fuel addition injector assembly are suspected.


a.

Disconnect the cable from the negative (-) battery terminal or remove the ECD fuse for 1 minute or more.


b.

Start the engine and race it to 3000 rpm several times.


c.

Check for white smoke in the exhaust gas. If found, check for a fuel odor or the smell of burning oil.

Result:
Result Proceed to
White smoke and a fuel odor are present. A
White smoke and a smell of burning oil are present. B
Except above C




A

3.PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSORY INSPECTION)

B

8.CHECK AND REPLACE TURBOCHARGER SUB-ASSEMBLY

C

10.CHECK FUEL INJECTION SYSTEM
3.PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSORY INSPECTION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / AF Lambda B1S1 and Exhaust Temperature B1S3.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S3
AF Lambda B1S1
50003 61 1063,55

e.

Drive the vehicle until the value of Exhaust Temperature B1S3 becomes 300°C (572°F) or more to activate the air fuel ratio sensors.

HINT:

Activation of the air fuel ratio sensor can be checked by confirming whether the value of AF Lambda B1S1 has changed from 1.99.



f.

Check that there is no problem on driving performance such as hesitation, knocking, rough idling, insufficient power and acceleration stumbling, or white smoke in emissions.

A241156
6.5,1.135 6.385,1.135 false 6.385,1.135 6.01,1.927 false 5.396,2.948 5.281,2.938 5.281,2.938 5.208,2.802 false 6.271,3.104 6.156,3.115 6.156,3.115 5.927,3.573 false 6.073,4.375 5.865,4.385 5.865,4.385 5.615,4.156 false 6.552,1.042 7.031,1.333 0.479,0.292 10 false Normal 5.427,2.875 6.073,3.167 0.646,0.292 10 false Abnormal 6.302,3.042 6.781,3.333 0.479,0.292 10 false Normal 6.229,4.313 6.875,4.604 0.646,0.292 10 false Abnormal 3.385,0.313 5.938,0.688 2.552,0.375 10 false Air Fuel Ratio Sensor Starter Operation 4.292,0.708 6.854,0.979 2.563,0.271 10 false After Air Fuel Ratio Sensor Activation 1.917,1.073 2.375,1.333 0.458,0.26 10 false 1.99 1.917,2.406 2.344,2.677 0.427,0.271 10 false 1.0 1.917,3.958 2.333,4.188 0.417,0.229 10 false 0 V 0.75,1.76 2.042,2.052 1.292,0.292 10 false AF Lambda B1S1 0.708,3.208 1.99,3.479 1.281,0.271 10 false AFS Voltage B1S1

HINT:
·

The air fuel ratio sensor does not operate until the vehicle has been driven for a period of time with an exhaust gas temperature of 200°C (392°F) or more.

·

Perform diagnosis when the air fuel ratio sensor is operating and active.

·

Normal condition in the illustration is only an example. "AF Lambda B1S1" changes depending on driving conditions. If it changes at the range more than 1.0, it is normal.



Result:
Result Proceed to
There is no problem with driving performance such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, but excessive white smoke is present in the exhaust gas A
Except above B


HINT:

If white smoke is present in the exhaust gas without any driving performance problems such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, fuel injected due to a malfunction in the exhaust fuel addition injector assembly is the suspected cause of the white smoke.




A

4.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

10.CHECK FUEL INJECTION SYSTEM
4.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
5.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
a.

Clean the fuel filter case and replace the fuel filter.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

6.PERFORM PM FORCED REGENERATION
6.PERFORM PM FORCED REGENERATION
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EMISSION CONTROL SYSTEM(for DPF)>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
OK
NG



OK

END

NG

10.CHECK FUEL INJECTION SYSTEM
7.GO TO DTC CHART

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK AND REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Check for oil leaks and white smoke from the turbocharger sub-assembly and perform any necessary repairs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>Turbocharger Oil Leak and White Smoke

HINT:

Other than a malfunction of the turbocharger subassembly, exhaust valve stem oil leaks are suspected.



Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61


Result:
Proceed to
NEXT



NEXT

END

10.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

11.CHECK INTAKE / EXHAUST SYSTEM
11.CHECK INTAKE / EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

12.CHECK AFTER TREATMENT CONTROL SYSTEM
12.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED