Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) J

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  Injector Circuit  


DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK INJECTOR DRIVER (POWER SOURCE)
a.

Disconnect the injector driver connectors.


b.
A204910C08
0.469,1.094 0.885,1.323 0.417,0.229 1.948,0.958 2.448,0.688 true 1.969,1.396 2.417,1.688 true 0.125,0.49 0.438,0.688 0.313,0.198 10 false *a 0.521,1.125 0.938,1.365 0.417,0.24 10 false C107 2.479,0.573 2.792,0.771 0.313,0.198 10 false +B 2.479,1.667 2.906,1.865 0.427,0.198 10 false GND
*a Front view of wire harness connector
(to Injector Driver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C107-2 (+B) - C107-4 (GND) Ignition switch ON 11 to 14 V



c.

Reconnect the injector driver connectors.


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 1 INTEGRATION RELAY (EDU RELAY)
2.INSPECT NO. 1 INTEGRATION RELAY (EDU RELAY)
a.

Inspect the No. 1 integration relay (EDU relay).

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - NO. 1 INTEGRATION RELAY)

NG

REPLACE NO. 1 INTEGRATION RELAY (EDU RELAY)

3.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the injector driver connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C107-2 (+B) - 1J-8 Always Below 1 Ω
C107-4 (GND) - Body ground Always Below 1 Ω
1J-5 - 1J-6 Always Below 1 Ω
C107-2 (+B) or 1J-8 - Body ground Always 10 kΩ or higher
1J-5 or 1J-6 - Body ground Always 10 kΩ or higher



e.

Reconnect the injector driver connector.


f.

Reinstall the No. 1 integration relay.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G156-12 (IREL) - 1J-7 Always Below 1 Ω
G156-12 (IREL) or 1J-7 - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reinstall the No. 1 integration relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR