Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › IGNITION SYSTEM
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052111 IGNITION SYSTEM G

2TR-FBE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

In this section, the terms "Cold" and "Hot" refer to the temperature of the coils. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).


PROCEDURE

Hide 1.PERFORM SPARK TEST

a.

Check for DTCs (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

NOTICE:

If any DTC is output, perform the troubleshooting procedures for that DTC.



b.

Check if sparks occur.


ii.

Install the spark plug to the ignition coil and connect the ignition coil connector.


iii.

Disconnect the 4 injector connectors.


iv.

Ground the spark plug.


v.

Visually check that sparks occur while the engine is being cranked.

NOTICE:
·

Be sure to ground the spark plug when checking.

·

If the ignition coil has been struck or dropped, replace it.

·

Do not crank the engine for more than 2 seconds.





c.

Check that the wire harness side connector of the ignition coil with igniter is securely connected.

Result:
Result Proceed to
NG Connect securely
OK Go to next step



d.

Perform a spark test on each ignition coil with igniter.

i.

If there is a cylinder where sparks do not occur, replace its ignition coil with the ignition coil of a cylinder where sparks occur normally.


ii.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating ignition coil.

Result:
Result Proceed to
OK Replace ignition coil with igniter
NG Go to next step




e.

Inspect the spark plug.

i.

Replace the spark plug with a normal one.


ii.

Perform spark test again.

Result:
Result Proceed to
OK Replace spark plug
NG Go to next step




f.

Check power supply to ignition coil with igniter.

i.

Turn the ignition switch to ON.


ii.

Check that there is battery voltage at the ignition coil positive (+) terminal.

Result:
Result Proceed to
NG Check wiring between ignition switch and ignition coil with igniter
OK Go to next step




g.

Check the camshaft position sensor (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P0340).


h.

Check the crankshaft position sensor (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P0335).


i.

Check the IGT signal circuit (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P0351).


j.

Disconnect the 4 injector connectors.



Hide 2.CHECK SPARK PLUG

a.
I039522
0.813,1.948 1.083,1.948 false 0.625,1.854 0.865,2.104 0.24,0.25 10 *1
*1 Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or higher


HINT:

If a megohmmeter is not available, perform the following simple inspection instead.




b.

Alternative inspection method:

i.

Quickly accelerate the engine to 4000 rpm 5 times.


ii.

Remove the spark plug.


iii.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage on its thread and insulator.

If there is damage, replace the spark plug. If not, reinstall the spark plug.

Recommended Spark Plug:
Manufacturer Product
DENSO FK20HR8-G



d.

Check and adjust the spark plug electrode gap.

Maximum electrode gap for used spark plug:

1.1 mm (0.0433 in.)


If the gap is more than the maximum, replace the spark plug.

Electrode gap for new spark plug:

0.7 to 0.8 mm (0.0276 to 0.0315 in.)


NOTICE:

When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.



e.
A301633

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Air pressure:

588 kPa (6.0 kgf/cm2, 85 psi)


Duration:

20 seconds or less


HINT:

Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.