Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P0051  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)  P0052  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)  


DESCRIPTION

Refer to DTC P2237 (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P2237).

HINT:
·

When either of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

The ECM provides a pulse-width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A303190
0.146,0.104 3.708,0.385 3.563,0.281 10 false Reference (System Diagram of Bank 1 Sensor 1): 0.427,1.052 0.927,1.406 0.5,0.354 10 false from Battery 1.302,0.938 1.563,1.135 0.26,0.198 10 false A/F 2.302,2.177 2.563,2.375 0.26,0.198 10 false A/F 0.271,2.74 0.979,3.115 0.708,0.375 10 false from MAIN Relay 3.479,1 3.74,1.198 0.26,0.198 10 false +B 3.885,0.875 4.354,1.073 0.469,0.198 10 false Heater 3.885,1.552 4.354,1.75 0.469,0.198 10 false Sensor 4.49,1 4.958,1.198 0.469,0.198 10 false HA1A 5.229,0.99 5.698,1.188 0.469,0.198 10 false HA1A 5.927,0.448 6.396,0.646 0.469,0.198 10 false ECM 4.5,1.667 4.969,1.865 0.469,0.198 10 false A1A+ 3.344,1.677 3.698,1.844 0.354,0.167 10 false A1A- 3.427,2.167 4.833,2.396 1.406,0.229 10 false Air Fuel Ratio Sensor 5.219,1.656 5.688,1.854 0.469,0.198 10 false A1A+ 5.198,2.344 5.552,2.51 0.354,0.167 10 false A1A- 6.354,1.771 6.844,2.135 0.49,0.365 10 false Duty Control



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) The air fuel ratio sensor heater current is below 0.8 A (1 trip detection logic).
·

Open in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater (for bank 1 sensor 1)

·

No. 1 integration relay (A/F relay)

·

ECM


Comes on DTC stored
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) An air fuel ratio sensor heater current failure (1 trip detection logic).
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater (for bank 1 sensor 1)

·

No. 1 integration relay (A/F relay)

·

ECM


Comes on DTC stored
P0051 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1) The air fuel ratio sensor heater current is below 0.8 A (1 trip detection logic).
·

Open in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater (for bank 2 sensor 1)

·

No. 1 integration relay (A/F relay)

·

ECM


Comes on DTC stored
P0052 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1) An air fuel ratio sensor heater current failure (1 trip detection logic).
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater (for bank 2 sensor 1)

·

No. 1 integration relay (A/F relay)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate air fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

CONFIRMATION DRIVING PATTERN

A198819
0.802,1.021 1.448,1.219 0.646,0.198 10 false 3000 rpm 1.031,1.75 1.448,1.979 0.417,0.229 10 false Idling 0.229,2.042 1.521,2.302 1.292,0.26 10 false Ignition Switch ON 1.906,2.177 2.177,2.479 0.271,0.302 10 false [A] 2.76,1.656 3.052,1.885 0.292,0.229 10 false [B] 4.021,0.865 4.344,1.135 0.323,0.271 10 false [C] 5.323,1.656 5.688,1.979 0.365,0.323 10 false [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 false 5 minutes or more 4.875,2.604 6.073,2.844 1.198,0.24 10 false 5 minutes or more 3.854,2.615 4.427,2.781 0.573,0.167 10 false 1 minute 5.958,3.021 6.167,3.219 0.208,0.198 10 false [E]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0031, P0032, P0051 or P0052.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the air fuel ratio sensor output voltage (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)
a.
A150242
0.365,2.063 0.729,2.281 0.365,0.219 0.365,1.76 0.729,1.979 0.365,0.219 1.875,1.896 2.333,1.604 true 0.104,0.094 0.438,0.49 0.333,0.396 10 false *a 2.396,1.49 2.76,1.896 0.365,0.406 10 false +B 0.792,2.104 1.156,2.458 0.365,0.354 10 false *B 0.385,2.083 0.781,2.292 0.396,0.208 10 false C148 0.781,1.781 1.167,2.083 0.385,0.302 10 false *A 0.385,1.792 0.781,2.01 0.396,0.219 10 false C150
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Disconnect the air fuel ratio sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C150-2 (+B) - Body ground Ignition switch ON 11 to 14 V
C148-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.INSPECT RELAY (A/F)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C150-1 (HA1A) - C130-2 (HA1A) Always Below 1 Ω
C148-1 (HA2A) - C130-1 (HA2A) Always Below 1 Ω
C150-1 (HA1A) or C130-2 (HA1A) - Body ground Always 10 kΩ or higher
C148-1 (HA2A) or C130-1 (HA2A) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the pending DTCs.

Result:
Result Proceed to
DTC is not output A
P0031, P0032, P0051 or P0052 is output B




A

B

5.INSPECT RELAY (A/F)

Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (A/F RELAY - AIR FUEL RATIO SENSOR, MAIN RELAY, BATTERY, BODY GROUND)

NG

REPLACE RELAY (A/F)

6.CHECK HARNESS AND CONNECTOR (A/F RELAY - AIR FUEL RATIO SENSOR, MAIN RELAY, BATTERY, BODY GROUND)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the air fuel ratio sensor connector.


d.

Remove the A/F relay from the engine room relay block and junction block assembly.


e.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C150-2 (+B) - A/F relay terminal 3 Always Below 1 Ω
C148-2 (+B) - A/F relay terminal 3 Always Below 1 Ω
A/F relay terminal 1 - 1J-5 Always Below 1 Ω
A/F relay terminal 5 - Battery positive terminal Always Below 1 Ω
A/F relay terminal 2 - Body ground Always Below 1 Ω
C150-2 (+B) or A/F relay terminal 3 - Body ground Always 10 kΩ or higher
C148-2 (+B) or A/F relay terminal 3 - Body ground Always 10 kΩ or higher
A/F relay terminal 1 or 1J-5 - Body ground Always 10 kΩ or higher
A/F relay terminal 5 or Battery positive terminal - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR