Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › CAMSHAFT(w/o Glow Plug Controller)
RM1840EF _51 Engine / Hybrid System _009573 1KD-FTV ENGINE MECHANICAL _0052147 CAMSHAFT(w/o Glow Plug Controller) A

1KD-FTV ENGINE MECHANICAL  CAMSHAFT(w/o Glow Plug Controller)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 4.REMOVE RADIATOR HOSE INLET

Hide 13.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 14.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)

Hide 16.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler)

Hide 19.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

Hide 29.REMOVE CAMSHAFT

a.
A060148
0.438,0.698 0.302,1.135 0.302,1.135 0.302,1.25 true 0.208,1.292 0.396,1.469 0.188,0.177 10 false *1
*1 Key Groove


Turn the camshaft with a wrench so that the key groove of the camshaft faces upward.


b.
A060147
1.146,1.354 1.271,1.531 0.125,0.177 10 true 1 0.677,0.958 0.802,1.135 0.125,0.177 10 false 2 0.938,1.125 1.063,1.302 0.125,0.177 10 true 3 2.99,0.229 3.115,0.406 0.125,0.177 10 false 4 2.542,0.01 2.667,0.188 0.125,0.177 10 true 5 2.729,0.073 2.854,0.25 0.125,0.177 10 false 6 1.75,1.042 1.875,1.219 0.125,0.177 10 true 7 1.24,0.646 1.365,0.823 0.125,0.177 10 false 8 1.448,0.813 1.573,0.99 0.125,0.177 10 true 9 2.083,0.156 2.271,0.333 0.188,0.177 10 false 11 2.438,0.49 2.625,0.667 0.188,0.177 10 true 10 2.198,0.323 2.385,0.5 0.188,0.177 10 true 12 2.052,0.74 2.24,0.917 0.188,0.177 10 true 13 1.667,0.375 1.854,0.552 0.188,0.177 10 false 14 1.833,0.563 2.021,0.74 0.188,0.177 10 true 15

Uniformly loosen the 15 bearing cap bolts in several passes in the sequence shown in the illustration.


c.

Remove the 15 bearing cap bolts, 5 bearing caps, oil seal and 2 camshafts.