Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE ASSEMBLY(w/o DPF) › 2011.10–2012.01
RM1840EF _51 Engine / Hybrid System _009574 2KD-FTV ENGINE MECHANICAL _0052171 ENGINE ASSEMBLY(w/o DPF) A

2KD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY(w/o DPF)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the 2 front engine mounting insulators with the 2 nuts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 2.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine.


Hide 4.REMOVE ENGINE FROM ENGINE STAND

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Remove the engine from the engine stand.


Hide 5.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine into the engine compartment.


b.

Install the engine with the 4 bolts and 4 nuts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


c.

Remove the 2 bolts and 2 engine hangers.


Hide 6.INSTALL REAR END PLATE

a.

Install the rear end plate with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 7.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Clean the bolts and their holes.


b.

Apply adhesive to 2 or 3 threads at the end of each bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
A072424
2.01,0.854 2.688,0.469 2.688,0.469 2.531,1.042 true 2.75,0.385 3.094,0.583 0.344,0.198 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  
09330-00021  


d.

Install the flywheel to the crankshaft.


e.
A114803
2,0.271 2.146,0.448 0.146,0.177 10 true 2 2.542,0.49 2.688,0.667 0.146,0.177 10 true 7 2.708,0.917 2.854,1.094 0.146,0.177 10 true 4 2.479,1.427 2.667,1.646 0.188,0.219 10 true 6 2.052,1.667 2.229,1.844 0.177,0.177 10 true 1 1.625,1.552 1.781,1.75 0.156,0.198 10 true 8 1.375,1.021 1.521,1.198 0.146,0.177 10 true 3 1.615,0.542 1.76,0.698 0.146,0.156 10 true 5

Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

NOTICE:

Do not start the engine for at least 1 hour after installation.


Torque:
178 N*m (1815 kgf*cm, 131 ft.*lbf)


Hide 8.INSTALL CLUTCH DISC ASSEMBLY

Hide 9.INSTALL CLUTCH COVER ASSEMBLY

Hide 10.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

Hide 11.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.


a.

Install the rear No. 1 engine mounting insulator with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 13.CONNECT COOLER COMPRESSOR ASSEMBLY

a.

Connect the cooler compressor with the 4 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 14.CONNECT WIRE HARNESS

a.

Connect the 4 ECM connectors.


b.

for 4WD:

Connect the 4WD control ECU connector.


c.

w/ EGR Cooler:

Connect the turbo motor driver connector.


d.

Connect the 3 injector driver connectors.


e.

Attach the clamp and connect the wire harness with the 2 nuts.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)


f.

Connect the ground cable with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


g.

Connect the 2 engine room junction block connectors.


h.

Connect the engine room junction block wire with the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


i.

Install the side engine room relay block cover.


j.

Install the upper relay block cover.


Hide 16.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose.


Hide 17.CONNECT FUEL HOSE

a.

Connect the 2 fuel hoses.


Hide 18.CONNECT PRESSURE FEED TUBE ASSEMBLY

a.

Connect the pressure feed tube.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



b.

Connect the oil reservoir to pump hose.


Hide 19.CONNECT HEATER HOSE

a.

Connect the 2 heater hoses.


Hide 20.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 24.INSTALL RADIATOR ASSEMBLY

Hide 25.INSTALL ENGINE COVER BRACKET (w/o EGR Cooler)

a.

Install the engine cover bracket with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 26.INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY (w/o EGR Cooler)

a.

Connect the pipe (with the 2 air hoses) and install the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Tighten the 2 clamps.


c.

Connect the vacuum hose to the gas filter.


d.

Connect the manifold absolute pressure sensor connector.


Hide 27.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/o EGR Cooler)

a.

Attach the 4 claws to the pins of the cover bracket to install the engine cover.


Hide 28.INSTALL INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR (w/ EGR Cooler)

Hide 29.INSTALL AIR CLEANER ASSEMBLY

a.

Connect the air cleaner hose.


b.

Install the cleaner with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


c.

Tighten the hose clamp.


d.

Connect the connector to the mass air flow meter connector.


Hide 30.INSTALL BATTERY TRAY

Hide 31.INSTALL BATTERY

Hide 32.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp with the bolt and nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 33.ADD POWER STEERING FLUID

Hide 36.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the washer nozzle hose.


c.

Adjust the hood (See page Vehicle Exterior>DOOR / HATCH>HOOD>ADJUSTMENT).


Hide 37.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 42.PERFORM REGISTRATION

a.

Perform registration of the injector compensation codes (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION).



Hide 49.INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 50.INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)