Home › Engine / Hybrid System › 2KD-FTV FUEL › COMMON RAIL(w/o DPF) › 2011.10–2012.01
RM1840EF _51 Engine / Hybrid System _009578 2KD-FTV FUEL _0052217 COMMON RAIL(w/o DPF) A

2KD-FTV FUEL  COMMON RAIL(w/o DPF)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ EGR Cooler)

Hide 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 5.REMOVE NO. 2 ENGINE UNDER COVER

Hide 6.DRAIN ENGINE COOLANT (w/ EGR Cooler)

Hide 8.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY (w/o EGR Cooler)

Hide 9.REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ EGR Cooler)

Hide 12.DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)

Hide 13.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)

Hide 14.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 15.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)

Hide 16.DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler)

Hide 17.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler)

Hide 18.REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler)

Hide 20.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

Hide 21.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 22.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

a.

Disconnect the 3 fuel hoses.


b.
A301699
0.073,0.094 0.385,0.292 0.313,0.198 10 false *A 0.104,2.417 0.417,2.615 0.313,0.198 10 false *B 2.969,1.01 3.281,1.208 0.313,0.198 10 false *1 2.99,3 3.302,3.198 0.313,0.198 10 false *1
*A w/ EGR Cooler
*B w/o EGR Cooler
*1 Union Bolt


Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.


Hide 23.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE (w/ EGR Cooler)

Hide 24.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE (w/o EGR Cooler)

Hide 26.REMOVE COMMON RAIL ASSEMBLY

NOTICE:

Do not remove the pressure discharge valve or fuel pressure sensor.


a.

Disconnect the 2 connectors.


b.
A231856

w/ EGR Cooler:

Remove the 2 bolts, common rail and No. 2 intake manifold insulator.


c.

w/o EGR Cooler:

Remove the 2 bolts and common rail.