Home › Engine / Hybrid System › 2KD-FTV FUEL › COMMON RAIL(w/o DPF) › 2011.10–2012.01
RM1840EF _51 Engine / Hybrid System _009578 2KD-FTV FUEL _0052217 COMMON RAIL(w/o DPF) A

2KD-FTV FUEL  COMMON RAIL(w/o DPF)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

When replacing the common rail, do not remove the foreign object mixing prevention caps of the common rail until just before the fuel inlet pipe and injection pipe are connected to the common rail.

·

After removing the fuel inlet pipe, clean it with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL COMMON RAIL ASSEMBLY

a.

w/ EGR Cooler:

Install the common rail and No. 2 intake manifold insulator with the 2 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


b.

w/o EGR Cooler:

Install the common rail with the 2 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


c.

Connect the 2 connectors.


Hide 5.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

a.

Temporarily install the No. 2 nozzle leakage pipe with the 3 bolts.


b.

Temporarily install a new gasket and the union bolt.


c.

Tighten the 3 bolts and union bolt.

Torque:
for bolt : 13 N*m (130 kgf*cm, 9 ft.*lbf)
for union bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the 3 fuel hoses.


Hide 7.TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

Hide 8.INSTALL NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler)

Hide 9.TEMPORARILY INSTALL INTAKE AIR CONNECTOR (w/ EGR Cooler)

Hide 10.TIGHTEN NO. 2 INTAKE AIR CONNECTOR AND INTAKE AIR CONNECTOR (w/ EGR Cooler)

Hide 11.TIGHTEN INTAKE AIR CONNECTOR AND INTAKE MANIFOLD (w/ EGR Cooler)

Hide 13.INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)

Hide 14.INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler)

Hide 15.CONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler)

Hide 16.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 17.CONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)

Hide 18.CONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)

Hide 20.INSTALL MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ EGR Cooler)

Hide 22.INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY (w/o EGR Cooler)

Hide 23.INSTALL DIESEL THROTTLE BODY ASSEMBLY (w/ EGR Cooler)

Hide 25.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 27.ADD ENGINE COOLANT (w/ EGR Cooler)