Home › Engine / Hybrid System › 2KD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD(w/o EGR Cooler) › 2011.10–2012.01
RM1840EF _51 Engine / Hybrid System _009590 2KD-FTV INTAKE / EXHAUST _0052342 INTAKE MANIFOLD(w/o EGR Cooler) A

2KD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD(w/o EGR Cooler)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL INTAKE MANIFOLD

A301888
0.573,1.646 0.729,1.844 0.156,0.198 10 false 1 3.188,0.594 3.344,0.792 0.156,0.198 10 false 2 1.563,1.688 1.719,1.885 0.156,0.198 10 false 3 2.844,1.656 3,1.854 0.156,0.198 10 false 4 2.563,1.135 2.719,1.333 0.156,0.198 10 false 5 1.458,1.135 1.615,1.333 0.156,0.198 10 false 6

a.

Temporarily install a new gasket and the intake manifold with the 2 nuts and 4 bolts.


b.

Tighten the 2 nuts and 4 bolts in the order shown in the illustration.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 2.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 4.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 5.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System)

Hide 6.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)

Hide 7.INSTALL INTAKE AIR CONNECTOR

a.

Install a new gasket and the intake air connector with the 2 nuts and bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 8.INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET

a.

Install the No. 2 intake air connector bracket with the 3 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 9.INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR System)

Hide 10.INSTALL VACUUM SWITCHING VALVE BRACKET (w/o EGR System)

a.

Install the vacuum switching valve bracket with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 11.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring to the engine oil level dipstick guide.


b.

Apply a small amount of clean engine oil to the O-ring.


c.

Install the engine oil level dipstick guide with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Install the injection pipe clamp with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Install the engine oil level dipstick.


Hide 12.INSTALL MANIFOLD STAY

A253486
2.365,0.382 2.505,0.53 0.14,0.149 10 A

a.

Install the manifold stay with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

The manifold stay indented area (labeled A) must face the manifold.



Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).