Home › Engine / Hybrid System › 2TR-FBE FUEL › FUEL INJECTOR › 2012.01–2012.04
RM1840EF _51 Engine / Hybrid System _009581 2TR-FBE FUEL _0052250 FUEL INJECTOR G

2TR-FBE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance between the terminals.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.


Hide 2.INSPECT INJECTION VOLUME AND LEAKAGE

a.

Check the injection volume.

CAUTION:

This test involves high-pressure fuel and electricity, therefore, safety precautions should be taken. Perform this test in a safe area and avoid any sparks and flames. Do not smoke.


i.

Discharge the fuel system pressure (See page Engine / Hybrid System>2TR-FBE FUEL>FUEL SYSTEM>PRECAUTION).


ii.

Remove the fuel hose from the fuel pressure pulsation damper (See page Engine / Hybrid System>2TR-FBE FUEL>FUEL PRESSURE PULSATION DAMPER>REMOVAL).


iii.

Remove the fuel hose from the fuel filter (See page Engine / Hybrid System>2TR-FBE FUEL>FUEL FILTER>REPLACEMENT).


iv.

Disconnect the fuel pressure regulator (See page Engine / Hybrid System>2TR-FBE FUEL>FUEL PRESSURE REGULATOR>REMOVAL).

NOTICE:

Do not disconnect the No. 2 fuel hose from the fuel pressure regulator.



v.
A253180
0.99,1.99 0.885,1.99 0.885,1.99 0.719,1.885 false 1.469,1.635 1.469,1.542 1.469,1.542 1.771,1.25 false 1,0.927 1.073,0.927 1.073,0.927 1.323,1.135 false 1.313,0.375 1.479,0.375 1.479,0.375 1.792,0.677 false 2.188,0.146 2.313,0.146 2.313,0.146 2.417,0.323 false 2.917,0.427 2.99,0.24 2.99,0.24 3.104,0.24 false 3.083,1.031 3.083,0.927 3.083,0.927 2.906,0.74 false 1.948,0.917 2.24,0.917 false 2.24,0.917 2.24,1.677 false 1.948,1.333 2.24,1.333 false 1.104,0.281 1.292,0.448 0.188,0.167 10 false *1 3.01,1.052 3.198,1.219 0.188,0.167 10 false *5 2.188,1.708 2.375,1.875 0.188,0.167 10 false *4 1.031,1.896 1.219,2.063 0.188,0.167 10 false *3 0.792,0.823 0.979,0.99 0.188,0.167 10 false *2 1.406,1.656 1.594,1.823 0.188,0.167 10 false *2 2.021,0.063 2.208,0.229 0.188,0.167 10 false *2 3.146,0.146 3.333,0.313 0.188,0.167 10 false *4
*1 SST (3 Way)
*2 SST (Hose)
*3 SST (Union)
*4 SST (Clip)
*5 SST (Fuel Tube Connector)


Assemble SST as shown in the illustration.

SST
09268-31012  (09268-41091, 09268-41120, 09268-41500, 95336-08070, 90467-13001)


vi.
A237740
1.115,1.604 1.427,1.604 0.313,0 2.438,0.219 2.323,0.219 2.323,0.219 2.052,0.781 false 2.49,0.125 2.688,0.313 0.198,0.188 10 false *1 0.917,1.51 1.094,1.698 0.177,0.188 10 false *2
*1 SST (Fuel Tube Connector)
*2 Fuel Filter


Connect SST to the fuel filter.


vii.
A237741
1.51,0.125 2.448,0.125 2.448,0.125 2.563,0.24 false 2.323,1.24 2.323,0.771 false 1.323,0.042 1.521,0.229 0.198,0.188 10 false *1 2.26,1.281 2.448,1.469 0.188,0.188 10 false *2
*1 SST (Union)
*2 Pressure Regulator


Connect SST to the pressure regulator fuel inlet with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Make sure that the O-ring is installed to the pressure regulator.



viii.

Install the O-ring to the fuel injector.


ix.
A223383
2.75,0.438 2.635,0.438 2.635,0.438 2.219,0.781 false 0.854,1.604 0.958,1.604 0.958,1.604 1.469,1.885 false 1.948,0.125 1.646,0.125 false 1.396,0.229 0.99,0.229 false 1.427,0.51 1.021,0.51 false 0.656,1.521 0.833,1.698 0.177,0.177 10 false *1 2.771,0.344 2.948,0.521 0.177,0.177 10 false *2 2.01,0.031 2.188,0.208 0.177,0.177 10 false *3 0.792,0.427 0.969,0.604 0.177,0.177 10 false *5 0.792,0.146 0.969,0.323 0.177,0.177 10 false *4
*1 Vinyl Tube
*2 SST (Clamp)
*3 SST (Hose)
*4 SST (Clip)
*5 SST (Adaptor)


Assemble SST as shown in the illustration.

SST
09268-31012  (09268-41110, 09268-41310, 95336-08070, 90467-13001)


x.

Put the injector into a graduated cylinder.

CAUTION:

Install a suitable vinyl tube onto the injector to contain the gasoline spray.



xi.

Operate the fuel pump.


xii.
A302983
1.844,0.708 1.844,0.375 false 1.802,0.74 2.115,0.938 0.313,0.198 10 false *1
*1 SST (Wire)
V100135

Connect


Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Standard injection volume:

95 to 115 cm3 (5.8 to 7.0 cu. in.) in 5 seconds


Difference between each injector:

20 cm3 (1.2 cu. in.) or less


If the result is not as specified, replace the fuel injector.



b.

Check the fuel leakage.

i.

In the condition above, disconnect the test probes of SST (wire) from the battery and check the fuel leakage from the injector.

Fuel leakage:

1 drop or less per 12 minutes