Home › Engine / Hybrid System › 1KD-FTV EMISSION CONTROL › EGR VALVE(w/o Glow Plug Controller) › 2012.01–2012.04
RM1840EF _51 Engine / Hybrid System _009584 1KD-FTV EMISSION CONTROL _0052287 EGR VALVE(w/o Glow Plug Controller) A

1KD-FTV EMISSION CONTROL  EGR VALVE(w/o Glow Plug Controller)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL NO. 2 EGR VALVE ASSEMBLY (w/ EGR Cooler)

a.

Using a 6 mm hexagon wrench, install the EGR valve adapter, No. 2 EGR valve, EGR cooler, 2 new gaskets, 3 plate washers with the 3 hexagon bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


b.

Using a 5 mm hexagon wrench, install the bolt labeled A.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

A302568
1.938,1.219 1.938,0.854 1.938,0.854 1.792,0.854 false 3.26,0.906 3.26,0.542 3.26,0.542 3.115,0.542 false 4.167,0.677 4.167,0.313 4.167,0.313 4.021,0.313 false 5.323,0.99 5.323,1.25 false 5.99,0.854 5.99,1.115 false 4.698,1.781 4.823,1.958 0.125,0.177 10 false A 5.25,1.292 5.458,1.479 0.208,0.188 10 false *2 5.917,1.156 6.125,1.333 0.208,0.177 10 false *4 6.344,0.771 6.594,0.969 0.25,0.198 10 false x 3 6.76,0.677 7.01,0.875 0.25,0.198 10 false x 3 1.583,0.75 1.802,0.938 0.219,0.188 10 false *1 2.938,0.458 3.125,0.635 0.188,0.177 10 false *2 3.823,0.219 4.021,0.406 0.198,0.188 10 false *3
*1 EGR Cooler *2 New Gasket
*3 No. 2 EGR Valve *4 EGR Valve Adapter



Hide 2.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.

w/ EGR Cooler:

i.

Install a new gasket and electric EGR control valve to the EGR valve adapter with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

HINT:

Make sure the claws of the gasket face the electric EGR control valve.


A151127
5.76,1.375 5.854,1.375 5.854,1.375 6.104,1.583 false 5.438,0.656 5.271,0.656 5.271,0.656 5.115,0.906 false 4.01,1.198 4.188,1.198 4.188,1.198 4.365,1.479 false 1.51,1 1.698,1 1.698,1 1.698,1.333 false 3.146,1.906 3.385,2.052 0.24,0.146 10 false x 2 1.344,0.927 1.531,1.083 0.188,0.156 10 false *1 3.813,1.115 4,1.271 0.188,0.156 10 false *2 5.49,0.583 5.677,0.74 0.188,0.156 10 false *3 5.583,1.302 5.771,1.458 0.188,0.156 10 false *4
*1 EGR Cooler *2 New Gasket
*3 Electric EGR Control Valve *4 Claw




b.

w/o EGR Cooler:

i.

Install a new gasket and the electric EGR control valve.



Hide 3.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/o EGR Cooler)

a.
G037199
0.313,0.74 0.479,0.74 0.479,0.74 0.677,1.177 true 2.552,0.167 2.448,0.167 2.448,0.167 2.115,0.292 true 0.115,0.656 0.302,0.813 0.188,0.156 10 true *1 2.604,0.083 2.792,0.24 0.188,0.156 10 false *1
*1 Claw


Install 2 new gaskets and the No. 1 EGR pipe with the 2 nuts and 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

HINT:

Make sure the claws of the gasket face the No. 1 EGR pipe.



Hide 4.TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

a.

Set a new gasket to the cylinder head.


b.
A151129
2.198,0.135 2.042,0.135 2.042,0.135 1.198,1.49 true 2.271,0.052 2.458,0.208 0.188,0.156 10 false *1
*1 New Gasket


Temporarily install the electric EGR control valve with No. 2 EGR valve and EGR cooler with the 2 nuts and bolt.

HINT:

Temporarily install the bolt so that the bolt head contacts the EGR cooler.



c.

Connect the vacuum hose to the No. 2 EGR valve.


d.

Connect the EGR valve position sensor connector.


Hide 5.INSTALL NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler)

a.

Set a new gasket labeled A to the No. 2 intake air connector as shown in the illustration.


b.

Insert the No. 2 intake air connector with the gasket into the electric EGR control valve.


c.

Install a new gasket labeled B to the electric EGR control valve side shown in the illustration.


Hide 6.TEMPORARILY INSTALL INTAKE AIR CONNECTOR (w/ EGR Cooler)

a.

Set a new gasket labeled C to the intake manifold.


b.

Temporarily install the intake air connector to the intake manifold with the 3 bolts.


c.

Temporarily install the intake air connector and electric EGR control valve with the 3 nuts shown in the illustration.

A302571
4.688,0.135 4.875,0.135 false 5.469,0.635 5.76,0.635 false 5.719,1.719 6.01,1.719 false 1.198,1.01 1.198,1.406 false 2.281,0.677 2.281,0.344 2.281,0.344 2.5,0.344 false 1.125,1.438 1.313,1.635 0.188,0.198 10 false *1 2.521,0.26 2.708,0.458 0.188,0.198 10 false *2 4.906,0.063 5.094,0.26 0.188,0.198 10 false *2 5.802,0.563 5.99,0.76 0.188,0.198 10 false *3 6.104,1.656 6.292,1.854 0.188,0.198 10 false *2 6.073,1.177 6.323,1.344 0.25,0.167 10 false x 3 6.646,1.135 6.896,1.302 0.25,0.167 10 false x 3 5.313,1.844 5.448,2.021 0.135,0.177 10 false C 4.135,0.115 4.281,0.281 0.146,0.167 10 false B 2.521,0.781 2.656,0.958 0.135,0.177 10 false A
*1 No. 2 Intake Air Connector *2 New Gasket
*3 Intake Air Connector - -



Hide 7.TIGHTEN NO. 2 INTAKE AIR CONNECTOR AND INTAKE AIR CONNECTOR (w/ EGR Cooler)

a.

Tighten the 3 nuts labeled A shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 8.TIGHTEN INTAKE AIR CONNECTOR AND INTAKE MANIFOLD (w/ EGR Cooler)

a.

Tighten the 3 bolts labeled B shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 9.TIGHTEN EGR COOLER (w/ EGR Cooler)

a.

Tighten the bolt labeled C shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Tighten the 2 nuts labeled D shown in the illustration.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

A302572
4.552,1.542 4.688,1.729 0.135,0.188 10 false A 4.76,2.354 4.896,2.531 0.135,0.177 10 false B 1.552,1.833 1.708,2.031 0.156,0.198 10 false C 1.052,2.865 1.198,3.052 0.146,0.188 10 false D


Hide 12.INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)

a.
A302573
1.156,1.406 1.292,1.573 0.135,0.167 10 false A 2.188,1.604 2.313,1.76 0.125,0.156 10 false B 2.771,1.208 2.896,1.365 0.125,0.156 10 false B

Temporarily install the No. 2 intake air connector bracket with the 3 bolts.


b.

Tighten the bolt labeled A.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Tighten the 2 bolts labeled B.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 14.INSTALL NO. 1 GAS FILTER WITH GAS FILTER BRACKET (w/ EGR Cooler)

Hide 15.CONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler)

a.

Connect the No. 3 water by-pass pipe with wire harness with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 16.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 17.CONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)

a.
A302574
2.031,0.167 2.156,0.333 0.125,0.167 10 false A 0.177,2.49 0.302,2.656 0.125,0.167 10 false A 0.875,1.354 1.031,1.552 0.156,0.198 10 false B 1.781,2.479 1.938,2.677 0.156,0.198 10 false B 0.927,1.677 1.167,1.875 0.24,0.198 10 false 90° 0.938,3.156 1.146,3.313 0.208,0.156 10 false *1 2.271,1.792 2.521,1.969 0.25,0.177 10 false *2 3.104,2.458 3.333,2.635 0.229,0.177 10 false *3 2.875,3.01 3.115,3.208 0.24,0.198 10 false 90°
*1 Lower Side
*2 Upper Side
*3 LH Side


Connect the No. 4 water by-pass hose to the EGR cooler.

HINT:
·

The direction of the hose clamp is indicated in the illustration.

·

Insert the outlet hose into the stopper.




Hide 18.CONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)

a.

Connect the No. 3 water by-pass hose to the EGR cooler.

HINT:
·

The direction of the hose clamp is indicated in the illustration.

·

Insert the outlet hose into the stopper.




b.

Install the clamp.


Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 21.ADD ENGINE COOLANT (w/ EGR Cooler)