Home › Engine / Hybrid System › 1KD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD(w/o Glow Plug Controller) › 2012.01–2012.04
RM1840EF _51 Engine / Hybrid System _009588 1KD-FTV INTAKE / EXHAUST _0052325 INTAKE MANIFOLD(w/o Glow Plug Controller) A

1KD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD(w/o Glow Plug Controller)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL INTAKE MANIFOLD

a.

Temporarily install a new gasket and the intake manifold with the 4 bolts and 2 nuts.

A260053
0.448,0.031 0.75,0.26 0.302,0.229 10 false *A 3.771,0.031 4.146,0.5 0.375,0.469 10 false *B 0.5,2.24 0.667,2.469 0.167,0.229 10 false 1 3.74,1.948 3.917,2.125 0.177,0.177 10 false 1 4.719,2.25 4.917,2.479 0.198,0.229 10 false 2 1.344,2.469 1.531,2.646 0.188,0.177 10 false 2 0.833,2.323 1.01,2.573 0.177,0.25 10 false 3 4.073,2.052 4.208,2.24 0.135,0.188 10 false 3 1.167,2.427 1.333,2.635 0.167,0.208 10 false 4 4.552,2.198 4.729,2.406 0.177,0.208 10 false 4 0.99,2.375 1.135,2.583 0.146,0.208 10 false 5 4.26,2.104 4.417,2.292 0.156,0.188 10 false 5 3.906,2 4.094,2.188 0.188,0.188 10 false 6 0.677,2.281 0.854,2.458 0.177,0.177 10 false 6
*A w/ EGR Cooler *B w/o EGR Cooler



b.

Tighten the 4 bolts and 2 nuts in the order shown in the illustration.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:
A301693
2.365,0.813 2,0.135 2,0.135 1.875,0.135 true 1.719,0.042 2.031,0.198 0.313,0.156 10 false *1
*1 No. 1 manifold insulator


·

When installing the intake manifold, make sure that the No. 1 manifold insulator is not pinched.

·

Make sure that the swirl control valve actuator is not damaged by surrounding parts.




c.

w/o EGR Cooler:

Connect the vacuum hose and connector to the vacuum switching valve.


d.

w/ EGR Cooler:

Install the common rail sub-harness connector to the intake manifold.


Hide 2.INSTALL INTAKE MANIFOLD INSULATOR (w/ EGR Cooler)

a.
A148159
1.833,3.146 1.25,3.146 true 1.719,4.125 1.125,4.125 true 1.792,3.667 1.198,3.667 true 1.01,3.563 1.177,3.708 0.167,0.146 10 false *2 1.063,3.063 1.219,3.208 0.156,0.146 10 false *1 0.927,4.031 1.104,4.177 0.177,0.146 10 false *3
*1 Intake Manifold
*2 Intake Manifold Insulator
*3 Common Rail


Install the intake manifold insulator with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 3.INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET (w/ EGR Cooler)

a.

Install the No. 3 intercooler support bracket with the bolt.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 6.INSTALL VACUUM CONTROL VALVE SET (w/ EGR Cooler)

a.
A149961
1.656,0.542 2.885,0.542 true 2.021,0.927 2.76,0.927 2.76,0.927 2.76,0.552 true 1.479,0.802 0.885,0.802 true 1.771,1.115 1.01,1.115 1.01,1.115 1.01,0.813 true 2.896,0.448 3.146,0.656 0.25,0.208 10 false *2 0.708,0.708 0.979,0.938 0.271,0.229 10 false *1
*1 Pink Paint Mark
*2 White Paint Mark


Install the vacuum control valve set with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Connect the 3 vacuum hoses and 2 connectors.

HINT:

When connecting the hoses, match the colors of the paint marks on the hoses to the colors of the paint marks on the swirl control valve as shown in the illustration.



Hide 7.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/o EGR Cooler)

Hide 8.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/o EGR Cooler)

Hide 10.INSTALL INTAKE AIR CONNECTOR (w/o EGR Cooler)

a.

Install a new gasket and the intake air connector with the bolt and 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 11.INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET (w/o EGR Cooler)

a.

Install the No. 2 intake air connector bracket with the 3 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 12.INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/o EGR Cooler)

Hide 13.TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

Hide 14.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring to the engine oil level dipstick guide.


b.

Apply a small amount of clean engine oil to the O-ring.


c.

Install the engine oil level dipstick guide with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Install the injection pipe clamp with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Install the engine oil level dipstick.


Hide 15.INSTALL MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ EGR Cooler)

a.

Install the manifold stay with vacuum switching valve with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:

Be sure to securely connect the vacuum transmitting hose.



b.
A260058
2.406,0.688 2.406,0.938 2.406,0.938 2.906,0.938 true 2.563,0.458 2.906,0.458 true 2.906,0.469 2.906,1.198 true 2.365,0.427 2.365,0.094 2.365,0.094 1.656,0.094 true 2.208,0.615 1.885,0.615 1.885,0.615 1.885,0.104 true 0.781,1.344 0.781,1.417 0.781,1.417 0.229,1.417 true 0.74,0.927 0.333,0.927 0.333,0.927 0.333,1.406 true 2.271,2.625 2.458,2.625 false 1.417,0.01 1.635,0.219 0.219,0.208 10 false *2 2.823,1.25 3.042,1.438 0.219,0.188 10 false *1 0.031,1.323 0.281,1.542 0.25,0.219 10 false *1 2.542,2.531 2.792,2.719 0.25,0.188 10 false *3
*1 Pink Paint Mark
*2 Yellow Paint Mark
*3 Blue Paint Mark


Connect the 4 vacuum transmitting hoses and 2 vacuum switching valve connector.


Hide 16.INSTALL MANIFOLD STAY (w/o EGR Cooler)

a.
A253486
2.365,0.385 2.635,0.646 0.271,0.26 10 false A

Install the manifold stay with vacuum switching valve with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

The manifold stay indented area (labeled A) must face the manifold.



Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 19.ADD ENGINE COOLANT (w/ EGR Cooler)