Home › Engine / Hybrid System › 1KD-FTV INTAKE / EXHAUST › EXHAUST MANIFOLD W/ TURBOCHARGER(w/o DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009588 1KD-FTV INTAKE / EXHAUST _0052321 EXHAUST MANIFOLD W/ TURBOCHARGER(w/o DPF) A

1KD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER(w/o DPF)  INSTALLATION  


PROCEDURE

Hide 1.CLEAN TURBOCHARGER SUB-ASSEMBLY

Hide 2.INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A211906
1.229,1.896 1.323,1.896 1.323,1.896 1.708,1.615 false 1.063,1.792 1.323,1.969 0.26,0.177 10 false *1
*1 New Gasket


Install a new gasket and No. 1 turbo water pipe with the bolt and 2 nuts.

Torque:
for bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for nut : 12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 3.INSTALL EXHAUST MANIFOLD

a.
A301821
3.031,2.854 2.885,2.854 2.885,2.854 2.76,2.708 false 3.073,2.75 3.385,2.948 0.313,0.198 10 false *1 1.302,1.677 1.458,1.875 0.156,0.198 10 false 1 1.99,1.667 2.146,1.865 0.156,0.198 10 false 2 0.313,1.625 0.469,1.823 0.156,0.198 10 false 4 2.938,1.542 3.094,1.74 0.156,0.198 10 false 6 0.417,0.354 0.573,0.552 0.156,0.198 10 false 3 1,0.354 1.156,0.552 0.156,0.198 10 false 7 2.031,0.354 2.188,0.552 0.156,0.198 10 false 8 2.917,0.354 3.073,0.552 0.156,0.198 10 false 5
*1 Collar
V100136

Engine Side


Install a new gasket, manifold, 8 new collars and 8 plate washers to the cylinder head with 8 new nuts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

NOTICE:
·

Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.

·

Tighten the nuts in the order shown in the illustration.




Hide 4.INSTALL TURBOCHARGER SUB-ASSEMBLY

a.

Temporarily install a new gasket and the turbocharger with 3 new nuts.

HINT:

It is easier to install the turbo oil inlet pipe if the 3 nuts are only loosely installed.



b.
A301791
5.427,0.896 5.083,0.458 5.083,0.458 4.885,0.458 true 5.698,1.25 5.875,1.49 5.875,1.49 6.073,1.49 false 5.458,3.188 5.458,3.073 5.458,3.073 5.292,2.927 true 2.354,3.115 2.354,2.75 false 1.333,2.188 1.188,1.948 1.188,1.948 1.021,1.948 false 1.792,1.448 1.646,1.208 1.646,1.208 1.479,1.208 false 2.271,3.177 2.583,3.333 0.313,0.156 10 false *1 5.385,3.24 5.698,3.396 0.313,0.156 10 false *2 6.156,1.396 6.469,1.552 0.313,0.156 10 false *3 4.677,0.365 4.99,0.521 0.313,0.156 10 false *4 1.427,2.865 1.708,3.167 0.281,0.302 10 false A 0.885,2.563 1.073,2.792 0.188,0.229 10 false B 1.188,3.375 1.458,3.635 0.271,0.26 10 false C 0.865,1.844 1.177,2 0.313,0.156 10 false *1 1.323,1.104 1.635,1.26 0.313,0.156 10 false *1
*1 New Gasket *2 Claw
*3 Narrow *4 Wide
V100135

Outside - -


Temporarily install the turbo oil inlet pipe.

HINT:

Before installing the turbo oil inlet pipe, clean it.


i.

Install a new gasket and the turbo oil inlet pipe with the 2 nuts, but only loosely install the nuts.

NOTICE:

The notch (narrow part) of the gasket must face the engine.



ii.

Install a new gasket and the turbo oil inlet pipe with the 2 bolts, but only loosely install the bolts.

NOTICE:

The claws of the gasket must face the turbo oil inlet pipe.



iii.

Install a new gasket and the turbo oil inlet pipe with the union bolt, but only loosely install the union bolt.


iv.

Temporarily install the turbocharger stay with the 2 bolts and nut.



c.

Tighten the 3 nuts of the turbocharger.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


d.

Tighten the 2 nuts labeled A.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


e.

Tighten the union bolt labeled B.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


f.

Tighten the 2 bolts labeled C.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


g.
A301829
2.094,1.729 2.25,1.927 0.156,0.198 10 false 3 2.333,1.625 2.49,1.823 0.156,0.198 10 false 2 2.375,1.365 2.604,1.604 0.229,0.24 10 false 1

Tighten the 2 bolts and nut of the turbocharger stay in the order shown in the illustration.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 5.INSTALL TURBINE OUTLET ELBOW

a.

Install a new gasket and the turbine outlet elbow with the 3 new nuts.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 6.INSTALL NO. 1 TURBO WATER HOSE

a.

Install the 2 No. 1 turbo water hoses.


Hide 7.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Temporarily install the No. 1 exhaust manifold heat insulator with the bolt.


Hide 8.INSTALL NO. 1 TURBO INSULATOR

a.

Temporarily install the No. 1 turbo insulator with the 2 bolts.


b.

Tighten the bolt of the No. 1 exhaust manifold heat insulator, and the 2 bolts of the No. 1 turbo insulator.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 9.INSTALL COMPRESSOR INLET ELBOW

a.

Install a new gasket and the compressor inlet elbow with the 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Connect the 2 connectors to the turbocharger.


c.

Attach the wire harness clamp.


Hide 10.INSTALL VENTILATION PIPE

a.

Connect the 2 ventilation hoses to the cylinder head cover and compressor inlet elbow.


b.

Install the ventilation pipe to the cylinder head with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 14.INSTALL FRONT FENDER SEAL

a.

Install the front fender seal with the 5 clips.


Hide 15.INSTALL FRONT FENDER APRON SEAL UPPER

a.

Install the front fender apron seal upper with the 5 clips.


Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).