Home › Engine / Hybrid System › 1KD-FTV INTAKE / EXHAUST › INTAKE SYSTEM(w/ Glow Plug Controller) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009588 1KD-FTV INTAKE / EXHAUST _0052327 INTAKE SYSTEM(w/ Glow Plug Controller) G

1KD-FTV INTAKE / EXHAUST  INTAKE SYSTEM(w/ Glow Plug Controller)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT INTAKE SYSTEM

a.

Check that there is no air suction or leaks at the points shown in the illustration.

A271944
0.438,1.49 0.563,1.49 0.563,1.49 0.792,1.927 false 0.563,2.719 0.969,2.719 false 0.521,4.354 0.927,4.354 false 1.854,4.885 2.104,4.885 false 2.385,4.406 2.51,4.406 2.51,4.406 2.635,4.354 false 3.323,3.719 3.198,3.719 3.198,3.719 3.083,3.865 false 2.844,0.26 2.969,0.26 2.969,0.26 3.188,0.698 false 5.844,2.313 5.719,2.313 5.719,2.313 5.427,2.438 false 3.865,2.188 3.74,2.188 3.74,2.188 3.51,2.438 false 4.844,4.948 4.719,4.948 4.719,4.948 4.615,4.906 false 5.917,4.948 5.792,4.948 5.792,4.948 5.563,5.198 false 2.031,6.875 2.156,6.875 2.156,6.875 2.323,6.708 false 4.688,0.427 4.563,0.427 4.563,0.427 4.333,0.865 false 5.771,3.167 5.646,3.167 5.646,3.167 5.354,3.292 false 0.24,1.385 0.469,1.552 0.229,0.167 10 false *1 0.354,2.615 0.583,2.792 0.229,0.177 10 false *2 0.281,4.25 0.479,4.448 0.198,0.198 10 false *3 1.646,4.781 1.854,5.01 0.208,0.229 10 false *4 2.177,4.302 2.448,4.479 0.271,0.177 10 false *5 3.385,3.625 3.635,3.823 0.25,0.198 10 false *6 2.604,0.167 2.854,0.333 0.25,0.167 10 false *8 5.875,2.219 6.24,2.458 0.365,0.24 10 false *10 3.969,2.094 4.25,2.26 0.281,0.167 10 false *7 4.917,4.844 5.25,5.052 0.333,0.208 10 false *12 6,4.865 6.271,5.115 0.271,0.25 10 false *13 1.75,6.75 2,6.927 0.25,0.177 10 false *14 4.792,0.333 5.031,0.573 0.24,0.24 10 false *9 5.844,3.073 6.271,3.375 0.427,0.302 10 false *11 0.135,0.125 0.448,0.323 0.313,0.198 10 false *A
*A for DPF - -
*1 Air Cleaner *2 Mass Air Flow Meter
*3 Turbocharger *4 Ventilation Pipe
*5 EGR Cooler *6 No. 2 EGR Valve
*7 Vacuum Switching Valve (for EGR By-pass Valve) *8 Intercooler
*9 Intake Air Temperature Sensor *10 Diesel Throttle Body
*11 Manifold Absolute Pressure Sensor *12 Electric EGR Control Valve
*13 No. 1 Vacuum Switching Valve (for Swirl Control Valve) *14 Vacuum Pump


A271923
0.438,1.49 0.563,1.49 0.563,1.49 0.792,1.927 false 0.542,2.719 0.948,2.719 false 0.542,4.354 0.948,4.354 false 1.844,4.875 2.094,4.875 false 2.396,4.427 2.521,4.427 2.521,4.427 2.646,4.375 false 3.323,3.719 3.198,3.719 3.198,3.719 3.083,3.865 false 2.844,0.24 2.969,0.24 2.969,0.24 3.188,0.677 false 5.844,2.333 5.719,2.333 5.719,2.333 5.427,2.458 false 3.958,2.188 3.833,2.188 3.833,2.188 3.604,2.438 false 4.854,4.948 4.729,4.948 4.729,4.948 4.625,4.906 false 5.833,4.208 5.708,4.208 5.708,4.208 5.521,5.01 false 6.406,4.438 6.281,4.438 6.281,4.438 6.094,5.24 false 2.042,6.896 2.167,6.896 2.167,6.896 2.333,6.729 false 4.688,0.427 4.563,0.427 4.563,0.427 4.333,0.865 false 5.781,3.198 5.656,3.198 5.656,3.198 5.365,3.323 false 0.229,1.406 0.49,1.583 0.26,0.177 10 false *1 0.292,2.615 0.51,2.813 0.219,0.198 10 false *2 0.323,4.292 0.552,4.51 0.229,0.219 10 false *3 1.625,4.813 1.854,5.021 0.229,0.208 10 false *4 2.208,4.323 2.479,4.531 0.271,0.208 10 false *5 3.365,3.615 3.646,3.823 0.281,0.208 10 false *6 2.615,0.156 2.885,0.385 0.271,0.229 10 false *8 5.938,2.229 6.302,2.469 0.365,0.24 10 false *10 3.99,2.094 4.24,2.24 0.25,0.146 10 false *7 4.917,4.854 5.26,5.083 0.344,0.229 10 false *12 5.906,4.115 6.219,4.354 0.313,0.24 10 false *13 6.5,4.344 6.771,4.583 0.271,0.24 10 false *14 1.802,6.823 2.104,7.031 0.302,0.208 10 false *15 4.781,0.313 5.083,0.552 0.302,0.24 10 false *9 5.844,3.104 6.167,3.323 0.323,0.219 10 false *11 0.146,0.104 0.458,0.302 0.313,0.198 10 false *A
*A for i-ART - -
*1 Air Cleaner *2 Mass Air Flow Meter
*3 Turbocharger *4 Ventilation Pipe
*5 EGR Cooler *6 No. 2 EGR Valve
*7 Vacuum Switching Valve (for EGR By-pass Valve) *8 Intercooler
*9 Intake Air Temperature Sensor *10 Diesel Throttle Body
*11 Manifold Absolute Pressure Sensor *12 Electric EGR Control Valve
*13 No. 1 Vacuum Switching Valve (for Swirl Control Valve) *14 No. 2 Vacuum Switching Valve (for Swirl Control Valve)
*15 Vacuum Pump - -



Hide 2.CHECK INTAKE AIR CONTROL SYSTEM

a.

Check for leakage or clogging between the air cleaner housing and turbocharger inlet and between the turbocharger outlet and cylinder head.

Condition Operation
Clogged air cleaner Clean or replace element
Hoses collapsed or deformed Repair or replace
Leakage from connections Check each connection and repair
Cracks in components Check and repair or replace


Hide 3.CHECK EXHAUST SYSTEM

a.

Check for leakage or clogging between the cylinder head and turbocharger inlet and between the turbocharger outlet and exhaust pipe.

Condition Operation
Deformed components Repair or replace
Foreign material in passages Remove
Leakage from components Repair or replace
Cracks in components Check and repair or replace


Hide 4.CHECK BOOST PRESSURE

a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Warm up the engine.

HINT:

Be sure to perform the inspection when the engine coolant temperature is between 75 and 90°C (167 and 194°F).



d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

Powertrain > Engine > Data List
Tester Display
MAF
MAP
Accel Position
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Fuel Press
Actual EGR Valve Pos.
EGR Close Lrn. Status
Target Booster Pressure
50003 61 319,314,404,368,369,370,371,54,578,427,610

e.
A176220
2.604,2.135 2.469,2.135 2.469,2.135 2.042,2.771 true 2.635,2.042 2.833,2.188 0.198,0.146 10 false *1
*1 Snapshot Record Button


Take a snapshot of the Data List items with the intelligent tester as shown in the illustration.

HINT:
·

Graphs can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.

·

The condition of the turbocharger can be determined by fully depressing the accelerator pedal while driving at 15 km/h (9 mph) in 2nd gear to accelerate the vehicle (obey all laws and regulations and pay attention to driving conditions while driving the vehicle), and then comparing MAP with Target Booster Pressure at an engine speed of 3000 rpm.




f.

Compare MAP with Target Booster Pressure.

Standard:

MAP is within 20 kPa of Target Booster Pressure when accelerating with accelerator pedal fully depressed.


HINT:
·

The inspection above is only for vehicles equipped with a manual transmission.

·

If the above driving inspection using the intelligent tester cannot be performed (e.g. due to road conditions), or if the vehicle is equipped with an automatic transmission, perform the following inspection.



i.

Warm up the engine.

HINT:

Be sure to perform the inspection when the engine coolant temperature is between 75 and 90°C (167 and 194°F).



ii.
A301673
0.344,0.469 0.479,0.469 0.479,0.469 0.906,0.969 true 2.542,0.469 2.813,0.313 2.813,0.313 2.958,0.313 true 2.333,0.833 3.052,0.833 true 1.813,0.969 1.542,0.729 1.542,0.729 1.385,0.729 true 0.073,0.417 0.438,0.573 0.365,0.156 10 true SST 2.99,0.219 3.302,0.417 0.313,0.198 10 false *1 3.125,0.75 3.375,0.979 0.25,0.229 10 true *2 1.177,0.625 1.49,0.823 0.313,0.198 10 false *3
*1 Manifold Absolute Pressure Sensor
*2 3-Way Connector
*3 Gas Filter


Using a 3-way connector, connect SST (turbocharger pressure gauge) between the manifold absolute pressure sensor and gas filter.

SST
09992-00242  


iii.

for Manual Transmission:

While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (4450 to 4750 rpm).

Standard pressure:

5 to 20 kPa (0.05 to 0.2 kgf/cm2, 0.7 to 2.9 psi)



iv.

for Automatic Transmission:

Move the shift lever to P or N, and then fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (4450 to 4750 rpm).

Standard pressure:

5 to 20 kPa (0.05 to 0.2 kgf/cm2, 0.7 to 2.9 psi)


If the pressure is below the standard, the following problems may be present.

·

The intake system or exhaust system has leakage or blockage.

·

The turbocharger sub-assembly is malfunctioning.

·

The electric EGR control valve does not close.

·

The diesel throttle body does not open.

·

The vacuum hose connected to the manifold absolute pressure sensor is cracked or disconnected.

·

The mass air flow meter sub-assembly is malfunctioning.

·

A fuel injector assembly is malfunctioning.


If the pressure is higher than the standard, check the turbocharger.



g.

Chart showing the suspected trouble areas when the pressure is below the standard.

HINT:
·

○: If a problem listed in the leftmost column of the chart exists, or if the part in the leftmost column of the chart has a malfunction, the value of the Data List item in the uppermost row of the chart will meet the conditions shown in the row labeled "Value which represents a malfunction".

·

The values in the chart are applicable when the engine coolant temperature is between 75 and 90°C (167 and 194°F).

·

The values in the chart are for vehicles equipped with a manual transmission. For vehicles with an automatic transmission, use these values as a reference only as they may differ from the actual values.

·

The values in the chart are valid in an area with an atmospheric pressure higher than 95 kPa (1.0 kgf/cm2, 14 psi). Standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). Atmospheric pressure decreases by 1 kPa (0.01 kgf/cm2, 0.1 psi) for every 100 m increase in altitude, and is also affected by the current weather conditions.

·

When the altitude increases, atmospheric pressure and MAP decrease.



Item MAP
(Absolute pressure inside intake manifold)
MAF
(Intake air flow rate)
Accel Position Actual Throttle Position Actual EGR Valve Position EGR Close Lrn. Status
(EGR valve fully closed position learning status)
Fuel Pressure Injection Feedback Val #1 (to #4)
Values taken from an actual normal vehicle
*1
- 150 g/sec. 100% 0% 0% OK - -3 to +3 mm3/st
Values which represent a malfunction
*1
MAP is below Target Booster Pressure by 25 kPa or more MAF is less than 90 g/sec. Accel Position is less than 90% Actual Throttle Position is not within 5% of Target Throttle Position Actual EGR Valve Position is not within 5% of Target EGR Valve Position NG
(Determined after performing learning)
Fuel Pressure is below Target Common Rail Pressure by 10 MPa or more (Check while condition steady) Outside of above range
Turbocharger ○ ○ - - - - - -
EGR valve does not close or has problem with movement ○ ○ - - ○
(Problem with EGR valve movement)
*2
○
(EGR valve does not close)
*2
- -
Problem with diesel throttle movement ○
(Intake airflow decreases)
○ - ○ - - - -
Accelerator pedal cannot be fully depressed or problem with accelerator pedal position sensor exists - ○ ○ - - - - -
Intake air system leakage or blockage ○ ○ - - - - - -
Exhaust gas leakage before turbocharger or blockage ○ ○ - - - - - -
Manifold absolute pressure sensor ○ ○ - - - - - -
Manifold absolute pressure sensor hose is disconnected ○ ○ - - - - - -
Mass air flow meter sub-assembly - ○ - - - - - -
Fuel system (injector, supply pump or common rail) ○ ○ - - - - ○
(Fuel injector leakage, decrease in pressure discharge valve relief pressure or valve is stuck)
○
*3

HINT:
·

*1: These values are measured when the transmission is in 2nd gear, the accelerator pedal is fully depressed, the vehicle is accelerating, and the engine speed is 3000 rpm.

·

*2: DTC P0400 may be stored at this time. If the actual EGR valve position follows the target EGR valve position slowly, a feeling of hesitation may occur.

·

*3: If Injection Feedback Val # of a cylinder is not within -3 to +3 mm3/st, the corresponding cylinder has a malfunction (injector or compression). However, in some cases the cylinder may be malfunctioning even if the value is within -3 to +3 mm3/st.




Hide 5.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR

a.

Inspect the power source voltage.

i.

Disconnect the manifold absolute pressure sensor connector.


ii.
A301674
2.052,1.063 2.167,1.25 2.167,1.25 2.26,1.25 true 1.698,1.073 1.479,0.938 1.479,0.938 1.333,0.938 false 0.063,0.031 0.375,0.188 0.313,0.156 10 false *a 2.313,1.167 2.896,1.365 0.583,0.198 10 true 3 VC (+) 0.917,0.844 1.333,1.021 0.417,0.177 10 true 1E (-)
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3 VC (+) - 1 E (-) Ignition switch ON 4.75 to 5.25 V


If the result is not as specified, inspect the wire harness or ECM.



iii.

Connect the manifold absolute pressure sensor connector.



b.

Check the power supply.

i.

Turn the ignition switch to ON.


ii.

Disconnect the vacuum hose from the manifold absolute pressure sensor.


iii.
A253987
1.823,0.146 2.26,0.375 0.438,0.229 1.823,0.417 2.26,0.646 0.438,0.229 1.906,1.01 2.104,1.969 2.104,1.969 2.104,2.125 true 2.146,1.156 2.76,1.615 2.76,1.615 2.76,1.698 true 1.854,1.073 1.385,1.833 1.385,1.833 1.25,1.833 true 1.865,1.01 1.396,0.542 1.396,0.542 1.24,0.542 true 1.76,2.115 2.49,2.365 0.729,0.25 10 false 5 (PIM +) 0.406,1.75 1.177,1.958 0.771,0.208 10 false 12 (PIM +) 0.406,0.448 1.167,0.677 0.76,0.229 10 false 6 (EPIM -) 2.406,1.708 3.052,1.948 0.646,0.24 10 false 14 (E2 -) 1.865,0.177 2.333,0.396 0.469,0.219 10 false C114 2.292,0.156 2.635,0.417 0.344,0.26 10 false *A 2.302,0.427 2.573,0.667 0.271,0.24 10 false *B 1.063,0.458 1.302,0.656 0.24,0.198 10 false *B 1.063,1.75 1.323,1.938 0.26,0.188 10 false *B 2.958,1.719 3.167,1.896 0.208,0.177 10 false *A 2.344,2.125 2.552,2.302 0.208,0.177 10 false *A 1.875,0.448 2.323,0.688 0.448,0.24 10 false C167 0.063,0.01 0.26,0.177 0.198,0.167 10 false *a
*A for DPF
*B for i-ART
*a Component with harness connected
(ECM)
V100135

Vacuum


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
for DPF:
C114-5 (PIM +) - C114-14 (E2 -)
for i-ART:
C167-12 (PIM +) - C167-6 (EPIM -)
13.3 kPa (100 mmHg, 3.94 in.Hg) 0.8 to 1.4 V
26.6 kPa (199 mmHg, 7.85 in.Hg) 0.5 to 1.0 V
40 kPa (300 mmHg, 11.81 in.Hg) 0.3 to 0.9 V


HINT:

The values in the "Condition" column are gauge pressures.


If the result is not as specified, replace the manifold absolute pressure sensor.


iv.
A253988
1.823,0.208 2.26,0.438 0.438,0.229 1.823,0.469 2.26,0.698 0.438,0.229 1.906,1 2.125,1.958 2.125,1.958 2.125,2.042 true 2.146,1.135 2.76,1.667 2.76,1.667 2.76,1.76 true 0.552,2.24 0.688,2.24 0.688,2.24 1.063,2.99 true 1.865,1.063 1.406,1.823 1.406,1.823 1.26,1.823 true 1.854,1.01 1.385,0.542 1.385,0.542 1.25,0.542 true 0.063,0.063 0.26,0.229 0.198,0.167 10 false *a 1.719,2.083 2.427,2.302 0.708,0.219 10 false 5 (PIM +) 0.365,1.75 1.198,2.021 0.833,0.271 10 false 12 (PIM +) 0.438,0.438 1.208,0.677 0.771,0.24 10 false 6 (EPIM -) 2.375,1.781 3.042,2.021 0.667,0.24 10 false 14 (E2 -) 1.875,0.25 2.344,0.479 0.469,0.229 10 false C114 2.281,0.229 2.531,0.49 0.25,0.26 10 false *A 2.292,0.51 2.531,0.729 0.24,0.219 10 false *B 1.073,0.448 1.281,0.625 0.208,0.177 10 false *B 1.021,1.76 1.229,1.938 0.208,0.177 10 false *B 2.927,1.792 3.229,2.01 0.302,0.219 10 false *A 2.313,2.083 2.521,2.26 0.208,0.177 10 false *A 1.875,0.51 2.344,0.781 0.469,0.271 10 false C167 0.198,2.167 0.625,2.396 0.427,0.229 10 false SST
*A for DPF
*B for i-ART
*a Component with harness connected
(ECM)
V100135

Pressure


Using SST, measure the voltage according to the value(s) in the table below.

SST
09992-00242  

Standard Voltage:
Tester Connection Condition Specified Condition
for DPF:
C114-5 (PIM +) - C114-14 (E2 -)
for i-ART:
C167-12 (PIM +) - C167-6 (EPIM -)
19.6 kPa (0.20 kgf/cm2, 2.84 psi) 1.0 to 1.7 V
39.2 kPa (0.40 kgf/cm2, 5.69 psi) 1.3 to 1.9 V
58.8 kPa (0.60 kgf/cm2, 8.53 psi) 1.5 to 2.2 V
78.5 kPa (0.80 kgf/cm2, 11.4 psi) 1.8 to 2.4 V
98.0 kPa (1.00 kgf/cm2, 14.2 psi) 2.1 to 2.7 V


HINT:

The values in the "Condition" column are gauge pressures.


If the result is not as specified, replace the manifold absolute pressure sensor.



Hide 6.CHECK MOTOR FOR TURBOCHARGER CONTROL OPERATION


b.

Check the stroke.

NOTICE:

Make sure the DC motor connectors are properly connected.


i.

Turn the ignition switch from ON to off.


ii.

Check the DC motor operation. Check that the motor rod stroke is as shown in A to C in the illustration below.


iii.

After the DC motor operates, visually check that the vane actuation link contacts the fully closed stopper.

OK:

When ignition switch is turned off, vane actuation link moves as shown in A through C in illustration below.

Vane actuation link and motor rod move smoothly when moving from position shown in A to that shown in B, and from position shown in B to that shown in C.


NOTICE:

Never loosen or tighten the lock nut of the fully closed stopper.


A301681
4.76,1.792 5.313,1.792 false 4.698,2.146 5.302,2.146 false 4.531,1.052 5,0.708 5,0.708 5.208,0.708 false 1.656,2.438 1.969,2.594 0.313,0.156 10 false *1 0.75,5.063 1.063,5.219 0.313,0.156 10 false *2 4.344,4.177 4.656,4.333 0.313,0.156 10 false *3 5.281,0.604 5.594,0.76 0.313,0.156 10 false *4 5.396,1.688 5.708,1.844 0.313,0.156 10 false *5 5.396,2.052 5.708,2.208 0.313,0.156 10 false *6 4.917,3.229 5.229,3.385 0.313,0.156 10 false *a 1.177,4.896 1.49,5.094 0.313,0.198 10 false ON 1.177,5.229 1.635,5.427 0.458,0.198 10 false OFF 1.906,4.375 2.063,4.573 0.156,0.198 10 false 0 1.771,4.25 1.927,4.448 0.156,0.198 10 false 0 1.385,3.396 2.615,3.594 1.229,0.198 10 false 5 (0.20) 1.396,2.719 2.625,2.917 1.229,0.198 10 false 9 (0.35) 0.583,2.521 2.115,2.719 1.531,0.198 10 false (mm (in.)) 1.917,0.313 2.208,0.615 0.292,0.302 10 false A 3.135,0.313 3.396,0.563 0.26,0.25 10 false B 4.594,0.333 4.885,0.604 0.292,0.271 10 false C 3.219,4.375 3.375,4.573 0.156,0.198 10 false 1 3.854,4.365 4.313,4.563 0.458,0.198 10 false 1.5 4.094,4.479 5.01,4.677 0.917,0.198 10 false (sec.)
*1 Motor Rod Stroke *2 Ignition Switch
*3 Ignition Switch Off Time *4 Motor Rod
*5 Lock Nut *6 Fully Closed Stopper
*a Fully Closed Stopper Contact - -


If the result is not as specified, check the ECM.