Home › Engine / Hybrid System › 1GR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD › from 2012.04
RM1840EF _51 Engine / Hybrid System _009592 1GR-FE INTAKE / EXHAUST _0052357 EXHAUST MANIFOLD A

1GR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

Hide 2.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.
A076439
2.823,1.083 2.823,0.917 2.823,0.917 3,0.917 false 3.063,0.823 3.219,0.969 0.156,0.146 10 false *1
*1 Oval Shape
V100135

Forward


Install a new gasket to the cylinder head LH with the oval shape facing rearward.

NOTICE:

Make sure the gasket is installed facing the proper direction.



b.

Install the exhaust manifold with 6 new nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Connect the air fuel ratio sensor connector.


Hide 3.INSTALL NO. 2 MANIFOLD STAY

a.

Install the No. 2 manifold stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 4.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 5.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

a.
A076440
1.781,1.469 1.094,0.844 1.094,0.844 0.75,0.844 true 0.542,0.76 0.708,0.958 0.167,0.198 10 false *1
*1 Oval Shape
V100135

Forward


Install a new gasket to the cylinder head RH with the oval shape facing forward.

NOTICE:

Make sure the gasket is installed facing the proper direction.



b.

Install the exhaust manifold with 6 new nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Connect the air fuel ratio sensor connector.


Hide 6.INSTALL MANIFOLD STAY

a.

Install the manifold stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 7.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Connect the front exhaust pipe to the exhaust pipe support.


b.

Install a new gasket to the end of the front exhaust pipe that connects to the exhaust manifold.

NOTICE:

Do not reuse the gasket.



c.

Connect the front exhaust pipe to the exhaust manifold with the 2 nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


d.
A111834

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

40.5 mm (1.59 in.)


If the free length is less than the minimum, replace the compression spring.


e.
A111803
3.021,0.958 3.021,1.51 true 2.938,1.594 3.115,1.802 0.177,0.208 10 false *1
*1 Gasket


Install a new gasket to the end of the front exhaust pipe that connects to the center exhaust pipe.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

When connecting the exhaust pipe, do not push in the gasket with the exhaust pipe.



HINT:

Using a plastic-faced hammer, uniformly tap the gasket so that the gasket and front exhaust pipe fit properly.



f.

Connect the front exhaust pipe to the center exhaust pipe and 2 compression springs with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 9.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 10.INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

Hide 11.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

Hide 12.INSTALL FRONT FENDER APRON SEAL UPPER LH

a.

Install the fender apron seal upper LH with the 5 clips.


Hide 13.INSTALL FRONT FENDER SEAL LH

a.

Install the fender seal LH with the 5 clips.


Hide 14.INSTALL FRONT FENDER APRON SEAL UPPER RH

a.

Install the fender apron seal upper RH with the 5 clips.


Hide 15.INSTALL FRONT FENDER SEAL RH

a.

Install the fender seal RH with the 5 clips.