Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY(for 1GR-FE) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052502 AUTOMATIC TRANSMISSION ASSEMBLY(for 1GR-FE) A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1GR-FE)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 6.REMOVE SHIFT LEVER BOOT ASSEMBLY

a.
C239519

Remove the 4 screws and shift lever boot.


Hide 7.REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY

a.

Fold back the transfer front drive shift boot.


b.
C213734

Using needle-nose pliers, remove the snap ring and pull out the shift lever.

HINT:

Move the transfer shift lever to the H4 position.



Hide 8.REMOVE NO. 1 ENGINE UNDER COVER

Hide 9.REMOVE NO. 2 ENGINE UNDER COVER

Hide 10.REMOVE NO. 3 ENGINE UNDER COVER

Hide 14.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY

Hide 15.DISCONNECT OIL COOLER TUBE

a.
C111240

Using a union nut wrench, disconnect the outlet tube and inlet oil cooler tube.


b.
C244708

Remove the 2 bolts and 2 clamps.


Hide 16.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C111231

Remove the nut and clip and disconnect the control cable.


Hide 17.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C111232

Remove the 2 bolts and control cable bracket from the transmission.


Hide 18.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a.
C111233

Support the transmission with a transmission jack.


Hide 19.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
G034256

Remove the 4 set bolts of the rear No. 1 engine mounting insulator.


b.

Remove the 4 nuts, 4 bolts and No. 3 frame crossmember.


Hide 20.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

G034260

a.

Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission.


Hide 21.DISCONNECT WIRE HARNESS

a.
C214940

Remove the nut and disconnect the ground cable.


b.
C112845

Tilt the transmission downward.

NOTICE:

Make sure the cooling fan does not contact the fan shroud.



c.

Disconnect the 8 connectors and detach the 7 clamps.

C263151


Hide 22.REMOVE STARTER ASSEMBLY

Hide 23.REMOVE DRIVE PLATE AND TORQUE CONVERTERSETTING BOLT

C111234

a.

Turn the crankshaft to gain access to each bolt.


b.

Hold the crankshaft pulley bolt with a wrench and remove the 6 torque converter clutch setting bolts.


Hide 24.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.
C111235

Remove the 9 bolts.


b.

Remove the automatic transmission assembly.

NOTICE:
·

Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.

·

Do not use excess force to pry on the transmission assembly.




Hide 26.REMOVE TORQUE CONVERTER ASSEMBLY