Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE(for 2WD) › from 2012.10
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052570 STEERING KNUCKLE(for 2WD) A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 3.REMOVE FRONT SPEED SENSOR LH (w/ ABS)

C113712

a.

Remove the bolt and disconnect the speed sensor.


b.

Remove the 3 bolts and disconnect the 3 clamps.


Hide 5.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH

F049868

a.

Remove the union bolt and gasket, and disconnect the brake hose from the brake cylinder.


b.

Remove the 2 bolts and brake cylinder.


Hide 7.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 8.DISCONNECT FRONT LOWER SUSPENSION ARM ASSEMBLY LH

a.
F049765

Remove the 2 bolts and disconnect the lower suspension arm from the steering knuckle.


Hide 9.DISCONNECT FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.
F049916
2.083,1.313 2.417,1.313 2.417,1.313 2.802,1.375 false 2.885,1.302 3.208,1.5 0.323,0.198 10 false SST

Support the front axle hub assembly with a jack.


b.

Remove the clip and nut.


c.

Using SST, disconnect the steering knuckle from the upper suspension arm.

SST
09628-62011  


Hide 10.REMOVE FRONT AXLE HUB ASSEMBLY

Hide 11.REMOVE KNUCKLE GREASE RETAINER CAP LH

a.
F049767

Using a screwdriver and hammer, tap out the knuckle grease retainer cap.


Hide 12.REMOVE FRONT AXLE HUB NUT LH

a.
F049768

Using a chisel and hammer, loosen the staked part of the hub nut.


b.
F049769

Remove the hub nut.


Hide 13.REMOVE ABS SPEED SENSOR ROTOR (w/ ABS)

a.

Remove the ABS speed sensor rotor.

NOTICE:

Take care not to scratch the serration of the speed sensor rotor.



Hide 14.REMOVE FRONT WHEEL INNER BEARING SPACER LH (w/o ABS)

a.

Remove the spacer.


Hide 15.REMOVE STEERING KNUCKLE LH

a.
F049860
1.26,1.281 0.479,0.656 0.479,0.656 1.021,0.729 true 0.115,0.542 0.5,0.74 0.385,0.198 10 false SST

Remove the 3 bolts, and shift the dust cover towards the hub (outside).


b.

Using SST, remove the steering knuckle.

SST
09710-30021  (09710-03051)
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04031, 09957-04010, 09958-04011)


c.

Remove the dust cover from the axle hub.

NOTICE:

Take care not to scratch the serration of the speed sensor rotor.



Hide 16.REMOVE FRONT AXLE HUB OIL SEAL LH

a.

Using a screwdriver, pry out the oil seal from the steering knuckle.


Hide 17.REMOVE FRONT AXLE HUB INNER BEARING LH

a.
F049861
1.51,1.292 0.604,0.552 0.604,0.552 1.625,0.552 true 0.25,0.458 0.646,0.667 0.396,0.208 10 false SST

Using snap ring pliers, remove the snap ring.


b.

Using SST and a press, press out the bearing from the steering knuckle.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07150)