Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) › from 2012.10
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052572 REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock)  DISASSEMBLY  


PROCEDURE

Hide 1.SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY

a.
C236647

Secure the differential carrier.


Hide 2.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 3.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C237323

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.07 mm (0.00276 in.)


If the runout is more than the maximum, replace the ring gear with a new one.



Hide 4.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C237324

Using a dial indicator, measure the backlash of the ring gear.

Standard backlash:

0.13 to 0.18 mm (0.00512 to 0.00708 in.)


If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 8.REMOVE NO. 4 TRANSFER INDICATOR SWITCH

a.
C237327
2.25,0.604 2.25,0.313 2.25,0.313 2.385,0.313 false 2.646,0.927 2.646,1.208 false 2.427,0.188 2.594,0.344 0.167,0.156 10 false *1 2.573,1.229 2.74,1.385 0.167,0.156 10 false *2
*1 Gasket
*2 Switch


Remove the switch and gasket.


Hide 9.REMOVE REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT

C237328
1.083,0.958 1.083,0.677 1.083,0.677 0.781,0.677 false 1.948,1.323 1.948,0.75 1.948,0.75 2.208,0.75 false 1.385,1.219 1.229,1.615 1.229,1.615 1.01,1.615 false 2.396,1.75 2.396,1.958 2.396,1.958 2.604,1.958 false 0.729,2.979 0.729,4.219 true 0.594,0.552 0.771,0.729 0.177,0.177 10 false *1 2.26,0.635 2.438,0.813 0.177,0.177 10 false *2 0.802,1.51 0.979,1.688 0.177,0.177 10 false *3 2.635,1.854 2.813,2.031 0.177,0.177 10 false *4 0.646,4.25 0.823,4.427 0.177,0.177 10 false *4
*1 Steel Ball
*2 Spring Seat
*3 Spring
*4 Screw Plug


a.

Using a 6 mm hexagon wrench, remove the 2 screw plugs.


b.

Remove the spring seat, spring and steel ball.


c.
C237329
2.167,0.979 2.167,0.104 2.167,0.104 2.094,0.104 true 2.385,0.594 2.385,0.135 2.385,0.135 2.563,0.135 true 2.417,1.073 2.104,1.979 2.104,1.979 1.948,1.979 true 1.927,0.021 2.104,0.188 0.177,0.167 10 false *1 2.594,0.042 2.771,0.208 0.177,0.167 10 false *2 1.771,1.896 1.948,2.063 0.177,0.167 10 false *3
*1 Shift Fork Shaft
*2 Pin Punch
*3 Slotted Spring Pin


Using a 5 mm pin punch and hammer, tap out the slotted spring pin from the shift fork shaft.


d.
C237330

Remove the 2 bolts from the shaft retainer.


e.

Using a plastic-faced hammer, tap on the retainer to separate it from the differential case.


f.

Remove the shift fork shaft.


Hide 11.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 13.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 14.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C282468
0.896,0.5 1.094,0.5 1.094,0.5 1.677,0.792 false 2.813,0.375 3.125,0.573 0.313,0.198 10 false *a 0.292,1.323 0.604,1.521 0.313,0.198 10 false *b 0.583,0.417 0.896,0.615 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the roller bearing (inner) from the drive pinion.

SST
09556-22010  


Hide 15.REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C237331

Remove the 2 bolts and 2 adjusting nut locks.


Hide 16.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C237332
1.792,1.594 1.792,1.896 1.792,1.896 0.76,1.896 false 1.74,1.479 1.594,1.479 1.594,1.479 1.594,1.896 false 0.563,1.792 0.781,2.01 0.219,0.219 10 false *a
*a Matchmark


Place matchmarks on the bearing cap and differential carrier.


b.

Remove the 4 bolts and 2 differential bearing caps.


c.

Remove the 2 adjusting nuts.


d.
C237333

Remove the rear differential case assembly from the differential carrier.

HINT:

Tag the 2 rear differential case bearings (outer) so that they can be reinstalled in the correct locations.



Hide 17.REMOVE DIFFERENTIAL DRIVE PINION

a.

Remove the drive pinion and bearing spacer from the differential carrier.


Hide 18.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C238710
1.983,0.574 2.298,0.574 false 2.333,0.494 2.644,0.643 0.311,0.149 10 SST

Using SST, remove the roller bearing (outer) from the carrier.

SST
09308-00010  


Hide 19.REMOVE DIFFERENTIAL OIL STORAGE RING

a.
C238707

Using a brass bar and hammer, tap out the oil storage ring from the carrier.


Hide 20.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 21.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C237336

Using a brass bar and hammer, tap out the rear tapered roller bearing (outer) from the carrier.

If the bearing is damaged during removal, replace it.


Hide 22.REMOVE DIFFERENTIAL RING GEAR

a.
C237337
1.198,1.208 2.865,1.208 true 1.208,1.125 2.302,1.125 2.302,1.125 2.302,1.208 true 2.896,1.115 3.135,1.354 0.24,0.24 10 false *a
*a Matchmark


Place matchmarks on the ring gear and differential case.


b.

Using a screwdriver and hammer, pry out the staked portions of the lock plates.


c.

Remove the 10 ring gear set bolts and 5 lock plates.


d.
C237338

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 25.DISASSEMBLE DIFFERENTIAL CASE

a.
C237340
1.25,1.563 2.604,1.563 true 1.26,1.656 2.271,1.656 2.271,1.656 2.271,1.563 true 2.625,1.479 2.875,1.698 0.25,0.219 10 false *a
*a Matchmark


Place matchmarks on the LH and RH cases.


b.

Remove the 8 bolts uniformly, a little at a time.


c.
C237341

Using a plastic-faced hammer, tap out the LH case from the RH case.


d.

Remove the rear differential lock sleeve from the differential case LH.


e.
C237342
1.302,0.156 1.083,0.156 false 1.052,0.688 1.052,0.448 1.052,0.448 0.448,0.448 false 0.677,0.781 0.406,0.781 false 1.438,1.115 0.594,1.115 false 0.927,1.396 0.479,1.396 false 0.865,1.698 0.865,1.833 0.865,1.833 0.583,1.833 false 1.833,0.604 2.115,0.167 2.115,0.167 2.323,0.167 false 2.229,0.885 2.594,0.885 false 2.25,1.24 2.354,1.24 2.354,1.24 2.354,0.885 false 2.396,0.635 2.792,0.635 false 2.469,1.5 2.771,1.5 false 1.833,1.969 2.385,1.969 false 1.844,1.635 1.917,1.74 1.917,1.74 2.052,1.74 false 0.854,0.063 1.052,0.26 0.198,0.198 10 false (2) 0.208,0.333 0.406,0.531 0.198,0.198 10 false (4) 0.177,0.677 0.375,0.875 0.198,0.198 10 false (5) 0.354,0.969 0.552,1.167 0.198,0.198 10 false (3) 0.25,1.281 0.448,1.479 0.198,0.198 10 false (4) 0.354,1.729 0.552,1.927 0.198,0.198 10 false (5) 2.365,0.031 2.563,0.229 0.198,0.198 10 false (1) 2.625,0.781 2.823,0.979 0.198,0.198 10 false (4) 2.833,0.5 3.031,0.698 0.198,0.198 10 false (5) 2.823,1.365 3.021,1.563 0.198,0.198 10 false (5) 2.448,1.854 2.646,2.052 0.198,0.198 10 false (2) 2.104,1.635 2.302,1.833 0.198,0.198 10 false (1)

Remove the following parts from the differential cases.

(1) Side gear (2 pieces)

(2) Side gear thrust washer (2 pieces)

(3) Spider

(4) Pinion gear (4 pieces)

(5) Pinion gear thrust washer (4 pieces)



Hide 26.INSPECT REAR DIFFERENTIAL LOCK SLEEVE

a.
C237343

Install the sleeve to the differential case LH and check that it moves smoothly.


b.

Install the sleeve to the side gear and check that it moves smoothly.


Hide 27.INSPECT SHIFT FORK AND SLEEVE

a.
C237344

Using a feeler gauge, measure the clearance between the shift fork and sleeve.

Standard clearance (reference):

0.15 to 0.35 mm (0.00591 to 0.0137 in.)



Hide 28.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that the differential pinion and differential side gear are not damaged.

If the differential pinion or differential side gear is damaged, replace the differential gear kit.



Hide 29.INSPECT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.