Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

The slip indicator light blinks during VSC and TRC operation.

Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If traction control or VSC turns off, the slip indicator light comes on.

When the transfer position is L4, VSC is prohibited and the VSC OFF indicator and slip indicator lights turn on.

CAUTION / NOTICE / HINT

NOTICE:
·

As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first (See page Drivetrain>VF2A TRANSFER / 4WD / AWD>TRANSFER SYSTEM>ON-VEHICLE INSPECTION).

·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode VSC OFF switch Normal, Unknown, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

f.

Check that the mode display changes according to VSC OFF switch operation.

OK:

The intelligent tester display changes according to VSC OFF switch operation.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIP INDICATOR LIGHT)

NG

3.INSPECT VSC OFF SWITCH
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIP INDICATOR LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Slip Indicator Light Slip indicator light Indicator light ON / OFF Observe the combination meter.
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Slip Indicator Light
50004 105 11

f.

When performing the Slip Indicator Light Active Test, check Slip Indicator Light in the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Slip Indicator Light Slip indicator light ON or OFF ON: Slip indicator light on
OFF: Slip indicator light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Slip Indicator Light
50003 105 53
Result:
Result Proceed to
Data List Display Data List Display When Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B




A

B

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
3.INSPECT VSC OFF SWITCH
a.

Turn the ignition switch off.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the VSC OFF switch connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-30 (CSW) - G84-3 Always Below 1 Ω
A36-30 (CSW) - Body ground Always 10 kΩ or higher
G84-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C199357
0.177,0.969 0.5,1.208 0.323,0.24 1.865,1.958 1.635,1.396 false 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 0.219,1.01 0.573,1.271 0.354,0.26 10 false A36 1.927,1.875 2.281,2.135 0.354,0.26 10 false EXI3
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-28 (EXI3) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G20 combination meter connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-3 (IND) - G20-17 (SLIP) Always Below 1 Ω
A36-3 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR