Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1403  Rear Speed Sensor RH Malfunction  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1404  Rear Speed Sensor LH Malfunction  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) Stored during Test Mode.
·

Rear speed sensor RH

·

Rear skid control rotor RH

·

Sensor installation


C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) Stored during Test Mode.
·

Rear speed sensor LH

·

Rear skid control rotor LH

·

Sensor installation


C1403 Rear Speed Sensor RH Malfunction One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that of the other sensors for 15 seconds or more.

2.

At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of less than 10 km/h (6 mph), the outputs from both rear speed sensors are 0 km/h (0 mph) for a cumulative time of 200 seconds.


·

Rear speed sensor RH

·

Rear skid control rotor RH

·

Sensor installation


C1404 Rear Speed Sensor LH Malfunction One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that of the other sensors for 15 seconds or more.

2.

At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of less than 10 km/h (6 mph), the outputs from both rear speed sensors are 0 km/h (0 mph) for a cumulative time of 200 seconds.


·

Rear speed sensor LH

·

Rear skid control rotor LH

·

Sensor installation



HINT:
·

DTCs C1403 and C1273 are for the rear speed sensor RH.

·

DTCs C1404 and C1274 are for the rear speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C108871
0.698,1.375 0.833,1.646 false 0.063,0.073 0.375,0.229 0.313,0.156 10 false *1 0.896,1.615 1.208,1.771 0.313,0.156 10 false *a 0.438,1.844 0.75,2 0.313,0.156 10 false *b 2.74,1.823 3.052,1.979 0.313,0.156 10 false *c
*1 Rear Speed Sensor
*a No clearance
*b CORRECT
*c INCORRECT


Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSTALLATION

OK:

The installation bolt is tightened properly.

There is no clearance between the sensor and rear axle housing.



Result:
Proceed to
OK
NG



OK

2.INSPECT SPEED SENSOR TIP

NG

2.INSPECT SPEED SENSOR TIP
a.

Turn the ignition switch off.



c.

Check the speed sensor tip.

OK:

No scratches, oil or foreign matter on the sensor tip.


NOTICE:

Do not replace the speed sensor if no damage to the speed sensor tip is found.


HINT:
·

If the sensor is contaminated with oil or other foreign material, clean the sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction. Therefore, confirm that the rotor is not contaminated with foreign material before replacing the sensor.




Result:
Proceed to
OK
NG



OK

3.INSPECT REAR SKID CONTROL ROTOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

3.INSPECT REAR SKID CONTROL ROTOR
a.

Turn the ignition switch off.


b.

Remove the rear axle shaft with backing plate.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>REMOVAL


c.

Check the rear skid control rotor.

OK:

No scratches, oil or foreign matter on the rotor.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SKID CONTROL ROTOR

4.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

f.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

NG

5.REPLACE REAR SPEED SENSOR
5.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.



Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

END

B

REPLACE REAR SKID CONTROL ROTOR