Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1405  Open or Short in Front Speed Sensor RH Circuit  C1406  Open or Short in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1405 Open or Short in Front Speed Sensor RH Circuit Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor RH

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)


C1406 Open or Short in Front Speed Sensor LH Circuit Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor LH

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTC C1405 is for the front speed sensor RH.

·

DTC C1406 is for the front speed sensor LH.



WIRING DIAGRAM

C281325
0.354,0.625 0.719,0.865 0.365,0.24 10 false A12 0.354,0.781 1.302,1.177 0.948,0.396 10 false Front Speed Sensor LH 0.396,1.771 0.76,2.01 0.365,0.24 10 false A11 0.385,1.948 1.333,2.344 0.948,0.396 10 false Front Speed Sensor RH 1.896,0.781 2.26,1.021 0.365,0.24 10 false FL+ 1.906,1.25 2.271,1.49 0.365,0.24 10 false FL- 1.896,1.969 2.26,2.208 0.365,0.24 10 false FR+ 1.906,2.448 2.271,2.688 0.365,0.24 10 false FR- 5.26,0.656 5.625,0.896 0.365,0.24 10 false 19 5.26,1.125 5.625,1.365 0.365,0.24 10 false 18 5.323,1.854 5.688,2.094 0.365,0.24 10 false 7 5.323,2.333 5.688,2.573 0.365,0.24 10 false 6 5.594,0.792 5.958,1.031 0.365,0.24 10 false FL+ 5.615,1.271 5.979,1.51 0.365,0.24 10 false FL- 5.604,1.969 5.969,2.208 0.365,0.24 10 false FR+ 5.615,2.448 5.979,2.688 0.365,0.24 10 false FR- 5.344,2.938 5.708,3.177 0.365,0.24 10 false A36 5.344,3.115 6.906,3.615 1.563,0.5 10 false Skid Control ECU (Brake Actuator Assembly) 2.313,0.646 2.677,0.885 0.365,0.24 10 false 1 2.323,1.146 2.688,1.385 0.365,0.24 10 false 2 2.333,2.333 2.698,2.573 0.365,0.24 10 false 2 2.323,1.844 2.688,2.083 0.365,0.24 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open circuit detection Error or Normal Normal -
FL Speed Open Front speed sensor LH open circuit detection Error or Normal Normal -
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor or disconnecting a connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

f.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A36-7 (FR+) - A11-1 (FR+) Always Below 1 Ω
A36-7 (FR+) - Body ground Always 10 kΩ or higher
A36-6 (FR-) - A11-2 (FR-) Always Below 1 Ω
A36-6 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A36-19 (FL+) - A12-1 (FL+) Always Below 1 Ω
A36-19 (FL+) - Body ground Always 10 kΩ or higher
A36-18 (FL-) - A12-2 (FL-) Always Below 1 Ω
A36-18 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (FR+, FL+ TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (FR+, FL+ TERMINAL)
a.

Turn the ignition switch off.


b.

Connect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the speed sensor connector.


d.
C190626
1.781,0.771 2.094,0.969 0.313,0.198 1.781,1.104 2.094,1.302 0.313,0.198 0.542,2.542 0.542,2.406 0.542,2.406 1.646,2.26 false 1.813,0.792 2.188,1.094 0.375,0.302 10 false A11 2.135,1.115 2.448,1.271 0.313,0.156 10 false *B 0.167,0.167 0.438,0.385 0.271,0.219 10 false *a 0.333,2.594 0.948,2.896 0.615,0.302 10 false FR+*A 0.333,2.865 0.979,3.125 0.646,0.26 10 false FL+*B 2.135,0.792 2.448,0.948 0.313,0.156 10 false *A 1.813,1.125 2.188,1.427 0.375,0.302 10 false A12
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A11-1 (FR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
A12-1 (FL+) - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

NG