Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

Refer to DTCs C1421, C1423 and C1424 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1281).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction When the stop light switch is off, the PMC terminal voltage is higher than 0.86 V for 5 seconds or more.
·

STOP fuse

·

Stop light switch

·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C237300
1.683,0.748 1.985,0.904 0.302,0.156 10 A24 1.683,0.93 3.465,1.142 1.781,0.212 10 Stop Light Switch Assembly 1.866,2.016 2.751,2.276 0.885,0.26 10 from Battery 0.752,2.212 1.186,2.403 0.434,0.191 10 STOP 1.54,0.279 1.7,0.497 0.16,0.219 10 2 2.741,0.272 2.901,0.49 0.16,0.219 10 1 5.386,0.305 5.521,0.499 0.135,0.194 10 2 5.641,0.408 5.961,0.589 0.319,0.181 10 STP 5.473,1.506 5.754,1.666 0.281,0.16 10 A36 5.473,1.663 7.101,2.011 1.628,0.347 10 Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1422 is output A
DTC C1422 and C1425 are output B




A

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

B

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

f.

Check that the stop light switch display observed on the intelligent tester changes according to the brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION

NG

5.CHECK TERMINAL VOLTAGE (STOP LIGHT POWER SOURCE CIRCUIT)
3.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch installation.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(w/ VSC)>INSTALLATION

OK:

The brake pedal height and stop light switch installation are normal.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

4.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1422 is not output A
DTC C1422 is output B




A

B

5.CHECK TERMINAL VOLTAGE (STOP LIGHT POWER SOURCE CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the stop light switch connector.


c.
C237276
1.563,0.354 1.854,0.542 0.292,0.188 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.594,0.365 2.073,0.615 0.479,0.25 10 false A24
*a Front view of wire harness connector
(to Stop Light Switch)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


c.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C199357
0.167,0.979 0.469,1.177 0.302,0.198 1.313,0.844 1.573,0.188 1.573,0.188 1.74,0.188 false 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 1.771,0.104 2.177,0.344 0.406,0.24 10 false STP 0.198,1 0.604,1.24 0.406,0.24 10 false A36
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-2 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR