Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE(for 4WD and Pre-Runner) › 2011.10–2012.01
RM1840EF _54 Brake _009627 PARKING BRAKE _0052635 PARKING BRAKE CABLE(for 4WD and Pre-Runner) A

PARKING BRAKE  PARKING BRAKE CABLE(for 4WD and Pre-Runner)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

C237689
2.01,0.698 2.01,0.573 2.01,0.573 1.719,0.573 false 4.948,6.073 4.948,6.49 4.948,6.49 5.656,6.49 false 1.563,0.49 1.729,0.656 0.167,0.167 10 false *2 5.688,6.417 5.854,6.583 0.167,0.167 10 false *1 4.094,4.979 4.229,5.135 0.135,0.156 10 false A 0.479,5.802 0.615,5.958 0.135,0.156 10 false A 1.813,3.323 1.948,3.479 0.135,0.156 10 false C 6.313,4.281 6.448,4.438 0.135,0.156 10 false B
*1 No. 3 Parking Brake Cable *2 No. 3 Clip


a.

Install the No. 3 parking brake cable with the 3 bolts and nut.

Torque:
for Bolt A, Nut C : 26 N*m (260 kgf*cm, 19 ft.*lbf)
for Bolt B : 14 N*m (143 kgf*cm, 10 ft.*lbf)


b.

Install the No. 3 clip.


c.

Connect the No. 3 parking brake cable to the parking brake shoe lever LH and backing plate LH.

i.

Connect the No. 3 parking brake cable to the backing plate with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


ii.

Connect the No. 3 parking brake cable to the parking brake shoe lever (See page Brake>BRAKE (REAR)>REAR BRAKE(for 4WD and Pre-Runner)>REASSEMBLY).



Hide 2.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

C281378
0.917,2.802 0.917,3.198 false 4.385,1.375 4.385,0.615 4.385,0.615 4.094,0.615 false 1.594,1.24 1.75,1.438 0.156,0.198 10 false A 3.26,3.156 3.417,3.354 0.156,0.198 10 false A 4.552,3.167 4.708,3.365 0.156,0.198 10 false A 6.344,0.406 6.5,0.604 0.156,0.198 10 false B 0.844,3.26 1.156,3.458 0.313,0.198 10 false *2 3.896,0.531 4.208,0.729 0.313,0.198 10 false *1
*1 No. 2 Parking Brake Cable *2 Parking Brake Equalizer


a.

Install the No. 2 parking brake cable with the 4 bolts.

Torque:
for Bolt A : 26 N*m (260 kgf*cm, 19 ft.*lbf)
for Bolt B : 14 N*m (143 kgf*cm, 10 ft.*lbf)


b.

Connect the No. 2 parking brake cable to the parking brake equalizer and apply MP grease to the connecting portion.


c.

Connect the No. 2 parking brake cable to the parking brake shoe lever RH and backing plate RH.

i.

Connect the No. 2 parking brake cable to the backing plate with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


ii.

Connect the No. 2 parking brake cable to the parking brake shoe lever (See page Brake>BRAKE (REAR)>REAR BRAKE(for 4WD and Pre-Runner)>REASSEMBLY).

HINT:

Use the same procedure described for the LH side.




Hide 3.INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY

C237687
4.406,0.49 2.313,0.49 true 2.979,3.146 2.979,1.729 2.979,1.729 2.323,1.729 true 4.438,2.302 2.969,1.094 2.969,1.094 2.563,1.094 true 5.823,2.552 5.583,2.323 5.583,2.323 5.438,2.323 false 2.115,0.396 2.385,0.563 0.271,0.167 10 false *3 2.385,1.01 2.646,1.167 0.26,0.156 10 false *2 2.146,1.635 2.427,1.813 0.281,0.177 10 false *1 5.271,2.219 5.531,2.385 0.26,0.167 10 false *4
*1 No. 1 Parking Brake Cable *2 No. 3 Parking Brake Cable
*3 Parking Brake Equalizer *4 Cable Support Bracket


a.

Connect the No. 1 parking brake cable to the parking brake lever (See page Brake>PARKING BRAKE>PARKING BRAKE LEVER>INSTALLATION).


b.

Install the No. 1 parking brake cable clamp to the No. 1 parking brake cable.


c.

Install the No. 1 parking brake cable with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the No. 1 parking brake cable to the parking brake equalizer.


e.

Connect the No. 1 parking brake cable to the No. 3 parking brake cable and apply MP grease to the connecting portion.


f.

Install the pin and No. 1 clip.


g.

Attach the No. 1 parking brake cable to the cable support bracket.


h.

Install the No. 1 heat insulator with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 5.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY AND NEW GASKET

Hide 7.ADJUST PARKING BRAKE

Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).