Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type) › 2012.01–2012.04
RM1840EF _56 Audio / Visual / Telematics _009633 PARK ASSIST / MONITORING _0052664 REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type) J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type)  Reverse Signal Circuit  


DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: for Automatic Transmission

*2: for Manual Transmission


WIRING DIAGRAM

E227687
0.281,1.427 2.875,1.615 2.594,0.188 10 false Park/Neutral Position Switch Assembly*1 5.177,1.365 5.604,1.552 0.427,0.188 10 false G152 5.177,1.5 6.417,1.885 1.24,0.385 10 false Navigation Receiver Assembly 0.281,1.271 0.604,1.458 0.323,0.188 10 false C26 1.667,0.781 1.927,0.969 0.26,0.188 10 false RL 5.323,0.771 5.656,0.958 0.333,0.188 10 false REV 5.135,0.635 5.271,0.823 0.135,0.188 10 false 2 0.427,2.625 0.75,2.813 0.323,0.188 10 false C27 1.948,0.656 2.073,0.844 0.125,0.188 10 false 1 1.938,2.01 2.083,2.198 0.146,0.188 10 false 1 0.427,2.792 2.573,2.979 2.146,0.188 10 false Back-up Light Switch Assembly*2 0.094,3.458 2.688,3.646 2.594,0.188 10 false *2: for Manual Transmission 0.094,3.177 2.688,3.365 2.594,0.188 10 false *1: for Automatic Transmission

PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E271492

Enter the "Function Check/Setting" screen and select "Connection status".

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R High
Except R Low


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK NAVIGATION RECEIVER ASSEMBLY
2.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E140414
1.427,0.448 2.031,0.729 0.604,0.281 0.896,1.365 0.615,1.177 0.615,1.177 0.5,1.177 true 0.063,0.063 0.302,0.25 0.24,0.188 10 *a 1.583,0.5 1.948,0.688 0.365,0.188 10 G152 0.156,1.094 0.49,1.26 0.333,0.167 10 REV
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the G152 navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G152-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
G152-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V


Result:
Result Proceed to
OK A
NG (for Automatic Transmission) B
NG (for Manual Transmission) C




A

B

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G152 navigation receiver assembly connector.


b.

Disconnect the C26 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G152-2 (REV) - C26-1 (RL) Always Below 1 Ω
G152-2 (REV) - Body ground Always 10 kΩ or higher


Rsult:
Result Proceed to
OK (for A340F) A
OK (for A343E) B
OK (for A343F) C
NG D




A

B

C

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G152 navigation receiver assembly connector.


b.

Disconnect the C27 back-up light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G152-2 (REV) - C27-1 Always Below 1 Ω
G152-2 (REV) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (for R151) A
OK (for R151F) B
NG C




A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR