Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY(for Double Cab) › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009647 SEAT BELT _0052734 FRONT SEAT OUTER BELT ASSEMBLY(for Double Cab) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for Double Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

B284037

a.

Insert the tip of the front shoulder belt anchor adjuster assembly to the body as shown in the illustration.


b.

Install the front shoulder belt anchor adjuster assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 2.INSTALL SHOULDER BELT ANCHORAGE PLATE COVER

B284032
1.833,0.969 1.583,0.75 1.583,0.75 0.979,0.75 true 1.708,3.031 1.5,2.958 1.5,2.958 0.948,2.958 true 0.781,0.656 1.021,0.865 0.24,0.208 10 false *b 0.75,2.854 0.948,3.042 0.198,0.188 10 false *a
*a Slide
*b Mark


a.

Install the shoulder belt anchorage plate cover as shown in the illustration.

HINT:

Make sure the shoulder belt anchorage plate cover is firmly set into the guides.



Hide 4.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B342490

w/o Pretensioner:

i.

Align the front seat outer belt assembly LH positioning holes with the 2 claws and install the retractor of the front seat outer belt assembly LH with the bolt.

Torque:
4.8 N*m (49 kgf*cm, 42 in.*lbf)



b.

Install the front seat outer belt shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B342527

w/ Pretensioner:

i.

Align the front seat outer belt assembly LH positioning holes with the 2 claws and install the retractor of the front seat outer belt assembly LH with the bolt.

Torque:
4.8 N*m (49 kgf*cm, 42 in.*lbf)


ii.
B342493

Connect the pretensioner connector as shown in the illustration.



d.

Install the front seat outer belt shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 5.INSTALL SEAT BELT ANCHOR COVER CAP

a.
B278421

Install the seat belt anchor cover cap with the 4 claws.


Hide 6.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Attach the 2 clips and 2 claws to install the lower center pillar garnish LH.


b.

Install the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 8.INSTALL REAR DOOR OPENING TRIM LH

HINT:

Use the same procedure described for the LH side.


Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).