Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2012.01–2012.04
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052749 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 1.INSTALL NO. 3 AIR DUCT

a.

Attach the 2 claws to install the No. 3 air duct.


Hide 2.TEMPORARILY INSTALL AIR CONDITIONING UNIT ASSEMBLY

a.

Temporarily install the air conditioning unit assembly with the bolt and nut.

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it, because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When installing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.




Hide 3.INSTALL NO. 1 COOLER UNIT DRAIN HOSE

a.

Install the No. 1 cooler unit drain hose.


Hide 4.INSTALL INSTRUMENT PANEL REINFORCEMENT

a.

Install the instrument panel reinforcement with the 8 bolts.

Torque:
for bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
for bolt B : 18 N*m (184 kgf*cm, 13 ft.*lbf)

E271840
1.333,0.76 1.646,0.76 true 1.26,1.01 1.438,1.01 1.438,1.01 1.438,0.771 true 1.146,1.292 1.281,1.292 1.281,1.292 1.281,1.469 false 1.198,1.51 1.51,1.667 0.313,0.156 10 false *A 1.708,0.677 2.021,0.833 0.313,0.156 10 false *1 1.604,1.021 1.917,1.177 0.313,0.156 10 false *2 0.854,1.26 1.167,1.417 0.313,0.156 10 false *2 0.125,2.74 0.438,2.896 0.313,0.156 10 false *1 6.844,1.25 7.156,1.406 0.313,0.156 10 false *1 6.844,1.51 7.156,1.667 0.313,0.156 10 false *1 2.844,1.302 3.156,1.458 0.313,0.156 10 false *2
*A for Manual Transmission - -
*1 Bolt A *2 Bolt B



b.

Temporarily install the 3 bolts.

E225190


c.

Connect the connectors.


d.

Attach the 12 clamps.


e.

Install the grommet to the vehicle body.


f.

Connect the ground wires to the instrument panel reinforcement with the 2 bolts.


g.

for Automatic Air Conditioning System:

Connect the 2 connectors and attach the clamp.


h.

for Manual Air Conditioning System:

Connect the 2 connectors and attach the clamp.


i.

Connect the connector and attach the 3 clamps.


Hide 6.INSTALL AIR CONDITIONING DUCT SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.

Attach the 2 claws to install the air conditioning duct sub-assembly.


Hide 7.INSTALL AIR CONDITIONING UNIT ASSEMBLY

a.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

E271841
3.063,1.76 3.219,1.958 0.156,0.198 10 false 1 3.917,1.552 4.073,1.75 0.156,0.198 10 false 3 4.938,1.365 5.094,1.563 0.156,0.198 10 false 2


b.
E227506

Temporarily install the screw.


c.
E271842
1.198,1.313 1.354,1.51 0.156,0.198 10 false 1 1.792,1.271 1.948,1.469 0.156,0.198 10 false 2

Tighten the bolt and nut in the order shown in the illustration.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 8.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

E271838
1.115,0.615 1.427,0.813 0.313,0.198 10 false *1 2.521,1.208 2.833,1.406 0.313,0.198 10 false *1 1.896,0.052 2.208,0.25 0.313,0.198 10 false *3 0.802,0.542 1.115,0.74 0.313,0.198 10 false *2 1.594,1.406 1.906,1.604 0.313,0.198 10 false *2 1.635,1.719 1.948,1.917 0.313,0.198 10 false *4
*1 Screw
*2 Nut A
*3 Nut B
*4 Bolt


a.

Install the driver side junction block with the 2 nuts labeled A.


b.

Connect the connectors.


c.

Attach the 2 clamps.


d.

Install the No. 1 instrument panel brace sub-assembly with the nut labeled B and bolt.

Torque:
for nut : 9.8 N*m (100 kgf*cm, 87 in.*lbf)


e.

Tighten the screw.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 9.INSTALL NO. 4 AIR DUCT

a.

Attach the 2 claws to install the No. 4 air duct.


Hide 10.INSTALL NO. 2 AIR DUCT

a.

Attach the 2 claws to install the No. 2 air duct.


Hide 11.INSTALL NO. 1 AIR DUCT

a.

Attach the 2 claws to install the No. 1 air duct.


Hide 12.INSTALL STEERING COLUMN ASSEMBLY

Hide 13.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 14.INSTALL DEFROSTER NOZZLE ASSEMBLY (w/ Defroster)

a.

Attach the 4 clips to install the defroster nozzle assembly.


Hide 15.INSTALL NO. 3 HEATER TO REGISTER DUCT

a.

Attach the 4 claws to install the No. 3 heater to register duct.


b.

Install the clip.


Hide 16.INSTALL NO. 1 HEATER TO REGISTER DUCT

a.

Attach the 3 claws to install the No. 1 heater to register duct.


b.

Install the clip.


Hide 17.INSTALL NO. 2 HEATER TO REGISTER DUCT

a.

Install the No. 2 heater to register duct with the 3 clips.


Hide 18.INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 19.CONNECT HEATER WATER OUTLET HOSE

E225470
0.818,2.364 0.992,2.548 0.175,0.184 10 *a 0.815,2.593 0.994,2.786 0.179,0.193 10 *b
*a Acceptable Range
*b 2 to 40°


a.

Connect the heater water outlet hose and attach the clip.


Hide 20.CONNECT HEATER WATER INLET HOSE

E225471
0.728,2.383 0.927,2.597 0.198,0.214 10 *a 0.728,2.622 0.908,2.79 0.179,0.168 10 *b
*a Acceptable Range
*b 2 to 40°


a.

Connect the heater water inlet hose and attach the clip.


Hide 21.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape attached to the air conditioning tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioning tube and accessory assembly.


d.

Connect the air conditioning tube and accessory assembly.


Hide 22.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape attached to the suction hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.


d.

Connect the suction hose sub-assembly and attach the piping clamp.

HINT:

After the connection, check that the claw of the piping clamp is attached.



e.

Install the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 29.CHECK SRS WARNING LIGHT (w/ Airbag System)