1.INSTALL NO. 1 BACK WINDOW GLASS STOPPER
| *1 | Vehicle Body |
| *2 | Stopper |
Install 2 new No. 1 back window glass stoppers to the vehicle body as shown in the illustration.
2.INSTALL NO. 2 BACK WINDOW GLASS STOPPER
| *1 | Ceramic Notch |
| *2 | Ceramic Line |
| *a | Backside |
Apply Primer G to the back window glass where the No. 2 back window glass stoppers will be installed.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.
Install 2 new No. 2 back window glass stoppers to the back window glass as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 40.0 mm (1.575 in.) |
| b | 16.3 mm (0.642 in.) |
3.INSTALL BACK WINDOW GLASS SPACER
| *1 | Ceramic Notch |
| *a | Backside |
Apply Primer G to the back window glass where the spacers will be installed.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.
Install 2 new back window glass spacers to the back window glass as shown in the illustration.
4.INSTALL NO. 1 BACK WINDOW MOULDING
Apply Primer G to the back window glass where the moulding and dam will be installed.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.
| *1 | Primer G | *2 | Dam Reference Line |
| *a | Backside | - | - |
| Area | Specified Condition |
|---|---|
| a | 6.4 mm (0.252 in.) |
| b | 12.7 mm (0.500 in.) |
| c | 7.5 mm (0.295 in.) |
Remove the peeling paper from the adhesive part of a new No. 1 back window moulding. Install the No. 1 back window moulding (adhesive side) to the back window glass (Primer G area) as shown in the illustration.
| *1 | Ceramic Notch | *2 | Dam Reference Line |
| *a | Backside | - | - |
| Area | Specified Condition |
|---|---|
| a | 6.4 mm (0.252 in.) |
5.INSTALL BACK WINDOW GLASS ADHESIVE DAM
Remove the peeling paper from the adhesive part of a new back window glass adhesive dam. Install the back window glass adhesive dam (adhesive side) to the back window glass (Primer G area) as shown in the illustration.
| *1 | Ceramic Notch | *2 | Dam Reference Line |
| *a | Backside | - | - |
| Area | Specified Condition |
|---|---|
| a | 7.5 mm (0.295 in.) |
6.INSTALL BACK WINDOW GLASS
| *1 | Primer M |
| *2 | Adhesive |
| *a | CORRECT |
| *b | INCORRECT |
Using a brush, apply Primer M to the exposed part of the vehicle body.
Allow the primer to dry for 3 minutes or more.
Do not apply Primer M to the adhesive.
Throw away any leftover primer.
Do not apply too much primer.
If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.
Using a brush or sponge, apply Primer G to the contact surface of the back window glass.
| *1 | Primer G | *2 | Adhesive Center Line |
| *a | Backside | - | - |
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.
Apply adhesive to the back window glass.
Toyota Genuine Windshield Glass Adhesive or equivalent
Cut off the tip of a cartridge nozzle as shown in the illustration.
After cutting off the tip, use all adhesive within the time written in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load A sealer gun with the cartridge.
Apply adhesive to the glass as shown in the illustration.
| *1 | Adhesive | *2 | Adhesive Center Line |
| *a | Backside | - | - |
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| c | 16.6 mm (0.654 in.) |
| d | 17.7 mm (0.697 in.) |
Install the back window glass to the vehicle body.
Lightly press the front surface of the back window glass to ensure that it is securely fit to the vehicle body.
Check that the spacers are attached to the vehicle body correctly.
Check that the vehicle body and back window glass have a small gap between them.
Hold the back window glass in place securely with protective tape or equivalent until the adhesive hardens.
Do not drive the vehicle for the amount of time written in the table below.
| Temperature | Minimum Time Prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
7.CHECK FOR LEAKS AND REPAIR
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
8.INSTALL ROOF HEADLINING ASSEMBLY
9.INSTALL ASSIST GRIP
10.INSTALL VISOR HOLDER LH
11.INSTALL VISOR HOLDER RH
12.INSTALL VISOR ASSEMBLY LH
13.INSTALL VISOR ASSEMBLY RH
14.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
15.INSTALL QUARTER INSIDE TRIM BOARD LH
16.INSTALL QUARTER INSIDE TRIM BOARD RH
17.INSTALL LOWER QUARTER TRIM PANEL LH
18.INSTALL LOWER QUARTER TRIM PANEL RH
19.INSTALL UPPER BACK PANEL GARNISH
20.INSTALL FRONT DOOR OPENING TRIM LH
21.INSTALL FRONT DOOR OPENING TRIM RH
22.INSTALL FRONT DOOR SCUFF PLATE LH
23.INSTALL FRONT DOOR SCUFF PLATE RH
24.INSTALL FRONT SEAT ASSEMBLY
for Bench Seat Type:
Install the front seat assembly (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>INSTALLATION).
for Separate Seat Type:
Install the front seat assembly (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Separate Seat Type)>INSTALLATION).