Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil.

The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit One of the following conditions is met (1 trip detection logic):
·

No crankshaft position sensor signal is sent to the ECM while cranking.

·

No crankshaft position sensor signal is sent to the ECM while the engine is running.

·

No crankshaft position sensor signal despite the VVT sensor signal input being normal after the engine is cranked.


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) The engine speed is 1000 rpm or more.
(b) The starter signal is off.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


- DTC stored

A107148
1.313,2.906 2.344,3.104 1.031,0.198 10 false 20 msec./DIV. 0.156,0.885 0.844,1.083 0.688,0.198 10 false 5 V/DIV. 0.177,1.573 0.458,1.771 0.281,0.198 10 false NE 0.094,2.052 0.458,2.25 0.365,0.198 10 false VV1 3.052,1.583 3.385,1.781 0.333,0.198 10 false GND 3.052,2.188 3.385,2.385 0.333,0.198 10 false GND 3.063,2.583 3.396,2.781 0.333,0.198 10 false GND 0.094,2.469 0.458,2.667 0.365,0.198 10 false VV2 0.333,0.26 2.74,0.458 2.406,0.198 10 false VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause noise in the waveforms.



Item Content
Terminal VV1+ - VV1-
VV2+ - VV2-
NE+ - NE-
Equipment Setting 5 V/DIV.,
20 msec./DIV.
Condition Cranking or idling


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the engine running, the ECM interprets this as a malfunction of the sensor.

If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0335 or P0339.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A160378
0.698,1.615 1.094,1.781 0.396,0.167 10 false C147 0.698,1.771 2.448,1.927 1.75,0.156 10 false Crankshaft Position Sensor 2.104,0.802 2.24,0.979 0.135,0.177 10 false 1 2.104,1.292 2.24,1.469 0.135,0.177 10 false 2 3.271,1.771 3.865,1.917 0.594,0.146 10 false Shielded 5.021,0.802 5.24,0.99 0.219,0.188 10 false 21 5.385,0.802 5.708,0.99 0.323,0.188 10 false NE+ 5.021,1.271 5.25,1.458 0.229,0.188 10 false 20 5.385,1.271 5.708,1.458 0.323,0.188 10 false NE- 5.552,2.021 5.969,2.188 0.417,0.167 10 false C129 5.552,2.167 5.938,2.333 0.385,0.167 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 and/or P0339 are output again, check the following items related to the VVT sensor.

·

Installation condition of the VVT sensor

·

Installation condition of the camshaft

·

Connection of the VVT sensor connector


·

If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.

·

Check the engine speed. The engine speed can be checked by using the intelligent tester. To check, follow the operation below:

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as less than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 61 315

e.

Start the engine.


f.

Read the values displayed on the tester while the engine is running.

OK:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the tester.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the tester remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C147-1 - C129-21 (NE+) Always Below 1 Ω
C147-2 - C129-20 (NE-) Always Below 1 Ω
C147-1 or C129-21 (NE+) - Body ground Always 10 kΩ or higher
C147-2 or C129-20 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
A295942
0.417,1.885 0.729,2.083 0.313,0.198 10 OK 2.667,1.885 2.979,2.083 0.313,0.198 10 NG 1.688,1.573 2.396,1.771 0.708,0.198 10 Clearance

Check the crankshaft position sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.CHECK CRANK ANGLE SENSOR PLATE (TEETH OF SENSOR PLATE)

NG

5.CHECK CRANK ANGLE SENSOR PLATE (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

6.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
P0335 or P0339 is output B


HINT:

If the engine does not start, replace the ECM.




A

END

B