Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

HINT:

This DTC relates to the oil control valve.


The Variable Valve Timing (VVT) system includes the ECM, intake camshaft timing oil control valve assembly and VVT controller. The ECM sends a target duty cycle control signal to the intake camshaft timing oil control valve assembly. This control signal regulates the oil pressure applied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the intake camshaft timing oil control valve assembly based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the intake camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A192077E04
4.427,0.815 6.408,1.027 1.981,0.212 10 Camshaft Position Sensor 4.427,1.325 6.521,1.486 2.094,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.268 1.551,0.253 10 VVT System: 2.333,1.96 3.61,2.135 1.277,0.175 10 Target Valve Timing 2.333,1.287 3.61,1.462 1.277,0.175 10 Actual Valve Timing 2.683,2.695 3.397,2.87 0.714,0.175 10 Correction 2.822,3.204 3.224,3.379 0.402,0.175 10 ECM 1.599,3.747 4.516,3.922 2.917,0.175 10 Camshaft Timing Oil Control Valve Assembly 0.166,2.69 0.861,2.865 0.695,0.175 10 Duty Cycle 4.427,1.827 6.017,1.981 1.589,0.154 10 Mass Air Flow Meter 4.427,2.854 6.78,3.043 2.353,0.189 10 Engine Coolant Temperature Sensor 4.427,2.344 6.211,2.512 1.784,0.168 10 Throttle Position Sensor 4.427,3.353 6.169,3.507 1.742,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 6.982,4.401 3.323,0.184 10 VVT Controller (Camshaft Timing Gear Assembly) 3.883,4.917 4.984,5.101 1.101,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0010 Camshaft Position "A" Actuator Circuit (Bank 1) An open or short in the camshaft timing oil control valve circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve circuit

·

Camshaft timing oil control valve assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A133814
0.292,2.083 2.156,2.563 1.865,0.479 10 false Camshaft Timing Oil Control Valve Assembly 1.49,0.854 1.625,1.031 0.135,0.177 10 false 2 1.49,1.583 1.625,1.76 0.135,0.177 10 false 1 0.292,1.906 0.646,2.146 0.354,0.24 10 false C74 5.448,0.854 6.021,1.208 0.573,0.354 10 false OC1+ 5.188,0.833 5.396,1.01 0.208,0.177 10 false 14 5.25,1.573 5.458,1.75 0.208,0.177 10 false 9 5.448,1.573 5.885,1.802 0.438,0.229 10 false OC1- 5.906,2.417 6.417,2.635 0.51,0.219 10 false C96 5.917,2.583 6.344,2.771 0.427,0.188 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).

Powertrain > Engine and ECT > Active Test
Tester Display
Control the VVT Linear (Bank1)
50004 234 32

e.

Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.

HINT:
·

When performing the Active Test, make sure the air conditioning is on.

·

Make sure the engine coolant temperature when the engine is started is 30°C (86°F) or less.



OK:
Tester Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [VVT OCV Duty #1 and VVT Change Angle #1].

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


b.
A183795E21
0.135,0.094 2.615,0.313 2.479,0.219 10 false Component without harness connected: 0.146,0.281 2.333,0.719 2.188,0.438 10 false (Camshaft Timing Oil Control Valve Assembly) 0.219,1.323 1.531,1.552 1.313,0.229 10 false Valve moves quickly

Connect the positive (+) battery terminal to terminal 1 and the negative (-) battery terminal to terminal 2. Check the valve operation.

OK:

Valve moves quickly.



c.

Reinstall the camshaft timing oil control valve assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C74-2 - C96-14 (OC1+) Always Below 1 Ω
C74-1 - C96-9 (OC1-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C74-2 or C96-14 (OC1+) - Body ground Always 10 kΩ or higher
C74-1 or C96-9 (OC1-) - Body ground Always 10 kΩ or higher



d.

Reconnect the camshaft timing oil control valve assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR