Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a Three-way Catalytic Converter (TWC) is used. For the most efficient use of the Three-way Catalytic Converter (TWC), the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel ratio. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the Three-way Catalytic Converter (TWC), and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with a heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post-Three-way Catalytic Converter (TWC) air-fuel ratio is lean (low voltage, i.e. below 0.45 V).

Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel ratio, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post-Three-way Catalytic Converter (TWC) air-fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air-fuel ratio after the Three-way Catalytic Converter (TWC) is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in primary air-fuel ratio control.

A115539
2.979,1.229 3.292,0.844 false 2.688,1.792 3.302,1.792 false 2.594,2.417 3.25,2.385 false 2.677,2.698 3.26,2.833 false 1.094,2.917 1.333,2.917 false 2.667,1.458 2.667,1.531 false 2.729,1.646 3.302,1.271 3.302,1.271 2.667,1.49 false 1.448,0.771 2.573,1.021 1.125,0.25 10 false Atmospheric Air 3.313,0.74 4.052,0.938 0.74,0.198 10 false Housing 3.323,1.188 4.854,1.385 1.531,0.198 10 false Platinum Electrode 3.958,0.927 4.927,1.125 0.969,0.198 10 false Output Voltage 5.01,0.938 6.396,1.135 1.385,0.198 10 false Ideal Air-fuel Mixture 2.01,3.146 2.906,3.344 0.896,0.198 10 false Exhaust Gas 3.344,1.698 4.448,1.917 1.104,0.219 10 false Solid Electrolyte 3.292,2.771 4.51,3.063 1.219,0.292 10 false Coating (Ceramic) 3.323,2.302 3.802,2.5 0.479,0.198 10 false Heater 1.365,2.823 1.802,3.031 0.438,0.208 10 false Cover 4.813,2.927 6.927,3.292 2.115,0.365 10 false Richer - Air-fuel Ratio - Leaner 3.344,1.865 4.458,2.188 1.115,0.323 10 false (Zirconia Element)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) Low voltage (open):
During active air-fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage output is below 0.21 V.

(b) Target air-fuel ratio is rich.


·

Open in heated oxygen sensor circuit

·

Heated oxygen sensor

·

Heated oxygen sensor heater

·

No. 1 integration relay

·

Gas leak from exhaust system

·

Air fuel ratio sensor


Comes on DTC stored

MONITOR DESCRIPTION

Active Air-fuel Ratio Control

The ECM usually performs air-fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air-fuel ratio. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the Three-way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).

Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Open in Heated Oxygen Sensor Circuit (DTC P0137)

During active air fuel ratio control, the ECM calculates the oxygen storage capacity* of the three-way catalytic converter by forcibly regulating the air fuel ratio to become rich or lean.

If the heated oxygen sensor has an open or short circuit, or the voltage output of the sensor noticeably decreases, this indicates that the oxygen storage capacity is an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air fuel ratio control, when the target air fuel ratio is rich and the heated oxygen sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137.

HINT:

*: The three-way catalytic converter has the capability to store oxygen. The oxygen storage capacity and the emission purification capacity of the three-way catalytic converter are mutually related.


A234468
5.813,3.792 6.021,4.052 false 4.292,2.042 4.448,1.75 false 4.448,1.75 4.594,1.75 false 5.344,2.396 5.448,1.75 false 5.448,1.75 5.625,1.75 false 5.698,3.01 5.844,2.583 false 5.844,2.583 6,2.583 false 0.063,0.052 3.823,0.448 3.76,0.396 10 false Heated Oxygen Sensor Circuit Low Voltage (P0137: Open) 0.281,1.344 2.698,1.552 2.417,0.208 10 false Active Air Fuel Ratio Control 0.281,3.333 3.083,3.542 2.802,0.208 10 false Heated Oxygen Sensor Voltage 0.281,2.125 2.281,2.313 2,0.188 10 false Target Air Fuel Ratio 2.083,2.042 2.979,2.396 0.896,0.354 10 false Stoichiometric Air Fuel Level 2.781,1.365 3.146,1.563 0.365,0.198 10 false Off 2.49,3.5 2.979,3.698 0.49,0.198 10 false 0.21 V 4.313,0.792 5.469,0.99 1.156,0.198 10 false 15 to 20 seconds 4.521,1.323 5.344,1.573 0.823,0.25 10 false Operating 4.667,1.656 5.229,1.854 0.563,0.198 10 false Normal 5.677,1.656 6.323,1.854 0.646,0.198 10 false Abnormal 6.063,4.052 6.802,4.25 0.74,0.198 10 false Abnormal 6.052,2.51 6.615,2.708 0.563,0.198 10 false Normal 4.729,2.438 5.094,2.635 0.365,0.198 10 false Rich


MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor
Required Sensors/Components (Related) Crankshaft position sensor, engine coolant temperature sensor, mass air flow meter, throttle position sensor and air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Heated Oxygen Sensor Output Voltage (Low Voltage)
Catalyst monitor precondition Met
Catalyst monitor precondition defined as when all of following conditions met: -
Battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa-a (570 mmHg-a) or higher
Idling OFF
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10 to 80%

TYPICAL MALFUNCTION THRESHOLDS

Heated Oxygen Sensor Output Voltage (Low)
Both of following conditions met (a) and (b)
(a) Commanded air-fuel ratio 14.4 or less
(b) Rear heated oxygen sensor voltage Below 0.21 V

CONFIRMATION DRIVING PATTERN

A301803
0.49,0.49 1.688,0.74 1.198,0.25 10 false 120 km/h (75 mph) 0.552,1.365 1.75,1.615 1.198,0.25 10 false 80 km/h (50 mph) 4.01,0.708 4.25,0.958 0.24,0.25 10 false [C] 5,3.313 5.24,3.563 0.24,0.25 10 false [D] 2.625,2.104 2.865,2.354 0.24,0.25 10 false [B] 2.021,2.427 2.26,2.677 0.24,0.25 10 false [A] 1.25,2.219 1.833,2.458 0.583,0.24 10 false Idling 0.521,2.469 1.719,2.719 1.198,0.25 10 false Ignition Switch ON 2.333,3 3.198,3.25 0.865,0.25 10 false Warming up 3.51,3.021 4.885,3.292 1.375,0.271 10 false 10 minutes or more

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

With the transmission in 4th gear or higher, drive the vehicle at a speed between 80 and 120 km/h (50 and 75 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0137.

12.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [D].




WIRING DIAGRAM

A247766
5.74,0.458 6.219,0.646 0.479,0.188 10 false HT1B 4.188,0.438 4.708,0.635 0.521,0.198 10 false HT1B 5.5,0.385 5.615,0.542 0.115,0.156 10 false 2 5.406,0.552 5.927,0.875 0.521,0.323 10 false C75 5.406,1.323 5.76,1.521 0.354,0.198 10 false C75 5.406,2.01 5.76,2.219 0.354,0.208 10 false C75 5.74,1.24 6.219,1.438 0.479,0.198 10 false OX1B 4.177,1.198 4.615,1.375 0.438,0.177 10 false OX1B 5.458,1.167 5.719,1.375 0.26,0.208 10 false 25 5.458,1.854 5.719,2.042 0.26,0.188 10 false 28 5.74,1.917 6.021,2.094 0.281,0.177 10 false E2 3.781,1.198 4.073,1.396 0.292,0.198 10 false E2 5.74,3.104 6.365,3.333 0.625,0.229 10 false MREL 5.5,2.948 5.615,3.104 0.115,0.156 10 false 8 5.396,3.104 5.781,3.313 0.385,0.208 10 false G89 4.969,2.385 5.719,2.708 0.75,0.323 10 false Shielded 3.406,1.667 5.031,1.979 1.625,0.313 10 false Heated Oxygen Sensor 3.406,1.542 3.781,1.75 0.375,0.208 10 false C88 3.792,0.438 4.125,0.635 0.333,0.198 10 false +B 6.198,3.854 6.604,4.052 0.406,0.198 10 false ECM 4.635,0.458 4.76,0.625 0.125,0.167 10 false 1 3.625,0.458 3.75,0.625 0.125,0.167 10 false 2 4.635,1.25 4.76,1.417 0.125,0.167 10 false 3 3.625,1.25 3.75,1.417 0.125,0.167 10 false 4 2.281,0.969 2.573,1.135 0.292,0.167 10 false 1J 2.323,0.823 2.438,0.979 0.115,0.156 10 false 2 2.281,0.531 2.531,0.698 0.25,0.167 10 false 1J 2.323,0.396 2.438,0.552 0.115,0.156 10 false 5 2.281,1.406 2.563,1.594 0.281,0.188 10 false 1J 2.323,1.271 2.438,1.427 0.115,0.156 10 false 3 0.552,1.583 0.833,1.76 0.281,0.177 10 false 1H 0.823,1.594 0.958,1.75 0.135,0.156 10 false 1 0.875,0.677 1.458,1.021 0.583,0.344 10 false EFI 1.469,1.292 2.021,1.563 0.552,0.271 10 false MAIN 0.75,2.51 1.521,2.75 0.771,0.24 10 false BATT P/I 0.927,3.771 1.594,4.052 0.667,0.281 10 false Battery 1.021,1.792 2.604,2.042 1.583,0.25 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine and turn the intelligent tester on.

3.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

5.

Perform the Active Test operation with the engine idling.

6.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the intelligent tester.



HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Intelligent Tester Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(A/F)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1
(A/F)
-12.5% Lean Higher than 3.4 V
O2S B1S2
(HO2)
+12.5% Rich Higher than 0.55 V
O2S B1S2
(HO2)
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A301859
0.135,0.688 0.75,0.885 0.615,0.198 10 false Case 0.844,0.635 2.906,1.021 2.063,0.385 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.427,0.625 5.573,1 2.146,0.375 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.948,0.635 7.052,1.01 1.104,0.375 10 false Main Suspected Trouble Area 6.427,2.208 6.719,2.479 0.292,0.271 10 false - 0.24,2.198 0.448,2.458 0.208,0.26 10 false 1 0.26,4.292 0.469,4.552 0.208,0.26 10 false 2 0.26,6.344 0.469,6.604 0.208,0.26 10 false 3 0.26,8.396 0.469,8.656 0.208,0.26 10 false 4 1.385,1.594 2,1.792 0.615,0.198 8 false +12.5% 1.417,1.823 2.031,2.021 0.615,0.198 8 false -12.5% 0.583,2.281 1.573,2.5 0.99,0.219 9 false Output Voltage 0.594,1.333 1.75,1.667 1.156,0.333 9 false Injection Volume 0.865,2.646 2.042,2.917 1.177,0.271 8 false Higher than 3.4 V 1.115,2.865 1.906,3.104 0.792,0.24 8 false Below 3.1 V 2.521,2.76 2.823,3.01 0.302,0.25 8 false OK 1.417,3.885 2.031,4.083 0.615,0.198 8 false -12.5% 1.396,3.656 2.01,3.854 0.615,0.198 8 false +12.5% 0.583,3.417 1.75,3.667 1.167,0.25 9 false Injection Volume 0.583,4.333 1.854,4.594 1.271,0.26 9 false Output Voltage 0.875,4.802 1.875,5.01 1,0.208 8 false Almost no reaction 2.552,4.719 2.938,5 0.385,0.281 8 false NG 1.427,5.938 2.042,6.135 0.615,0.198 8 false -12.5% 1.406,5.729 2.021,5.927 0.615,0.198 8 false +12.5% 0.583,5.469 1.677,5.667 1.094,0.198 9 false Injection Volume 0.583,6.417 1.635,6.656 1.052,0.24 9 false Output Voltage 0.865,6.76 1.917,6.917 1.052,0.156 8 false Higher than 3.4 V 1.115,6.979 1.906,7.219 0.792,0.24 8 false Below 3.1 V 2.531,6.865 2.833,7.115 0.302,0.25 8 false OK 0.583,7.5 1.583,7.708 1,0.208 9 false Injection Volume 1.427,8.01 2.042,8.208 0.615,0.198 8 false -12.5% 1.396,7.802 2.01,8 0.615,0.198 8 false +12.5% 0.583,8.438 1.635,8.667 1.052,0.229 9 false Output Voltage 0.865,8.927 1.823,9.125 0.958,0.198 8 false Almost no reaction 2.563,8.854 2.948,9.135 0.385,0.281 8 false NG 3.25,1.333 4.427,1.635 1.177,0.302 9 false Injection Volume 4.021,1.594 4.635,1.792 0.615,0.198 8 false +12.5% 4.042,1.813 4.656,2.01 0.615,0.198 8 false -12.5% 3.25,2.271 4.281,2.5 1.031,0.229 9 false Output Voltage 3.49,2.604 4.667,2.813 1.177,0.208 8 false Higher than 0.55 V 3.813,2.844 4.604,3.083 0.792,0.24 8 false Below 0.4 V 5.198,2.708 5.5,2.958 0.302,0.25 8 false OK 3.25,3.417 4.427,3.604 1.177,0.188 9 false Injection Volume 4.042,3.875 4.656,4.073 0.615,0.198 8 false -12.5% 4.01,3.667 4.625,3.865 0.615,0.198 8 false +12.5% 3.25,4.333 4.396,4.583 1.146,0.25 9 false Output Voltage 3.448,4.698 4.521,4.917 1.073,0.219 8 false Higher than 0.55 V 3.76,4.927 4.594,5.167 0.833,0.24 8 false Below 0.4 V 5.208,4.813 5.51,5.063 0.302,0.25 8 false OK 6.083,3.615 6.906,4.01 0.823,0.396 8 false Air fuel ratio sensor 6.094,4 6.854,4.573 0.76,0.573 8 false Air fuel ratio sensor heater 6.083,4.563 6.844,5.146 0.76,0.583 8 false Air fuel ratio sensor circuit 5.917,3.604 6.083,3.792 0.167,0.188 10 false - 5.917,3.99 6.083,4.177 0.167,0.188 10 false - 5.917,4.542 6.083,4.729 0.167,0.188 10 false - 4.042,5.948 4.656,6.146 0.615,0.198 8 false -12.5% 4.021,5.75 4.635,5.948 0.615,0.198 8 false +12.5% 3.25,5.469 4.354,5.729 1.104,0.26 9 false Injection Volume 3.25,6.417 4.198,6.667 0.948,0.25 9 false Output Voltage 3.5,6.865 4.552,7.052 1.052,0.188 8 false Almost no reaction 5.177,6.781 5.563,7.063 0.385,0.281 8 false NG 3.25,7.5 4.417,7.698 1.167,0.198 9 false Injection Volume 4.031,8 4.646,8.198 0.615,0.198 8 false -12.5% 4.01,7.813 4.625,8.01 0.615,0.198 8 false +12.5% 3.479,8.938 4.521,9.104 1.042,0.167 8 false Almost no reaction 5.156,8.854 5.542,9.135 0.385,0.281 8 false NG 3.26,8.417 4.333,8.667 1.073,0.25 9 false Output Voltage 6.083,5.438 6.927,5.75 0.844,0.313 8 false Heated oxygen sensor 6.073,5.958 6.896,6.333 0.823,0.375 8 false Heated oxygen sensor heater 6.073,6.646 6.917,7.25 0.844,0.604 8 false Heated oxygen sensor circuit 5.917,5.948 6.083,6.135 0.167,0.188 10 false - 5.917,5.417 6.083,5.604 0.167,0.188 10 false - 5.917,6.615 6.083,6.802 0.167,0.188 10 false - 6.083,7.531 6.948,7.906 0.865,0.375 8 false Fuel injector assembly 6.083,7.917 6.833,8.167 0.75,0.25 8 false Fuel pressure 6.094,8.177 6.917,9.281 0.823,1.104 8 false Gas leak from exhaust system (air-fuel ratio extremely rich or lean) 5.917,7.521 6.083,7.708 0.167,0.188 10 false - 5.917,7.906 6.083,8.094 0.167,0.188 10 false - 5.917,8.156 6.083,8.344 0.167,0.188 10 false -

HINT:
·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.READ OUTPUT DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P0137 is output A
P0137 and other DTCs are output B




A

2.CHECK FOR EXHAUST GAS LEAK

B

2.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leakage.

OK:

No gas leakage.



Result:
Proceed to
OK
NG



OK

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C88-1 (HT1B) - C75-2 (HT1B) Always Below 1 Ω
C88-3 (OX1B) - C75-25 (OX1B) Always Below 1 Ω
C88-4 (E2) - C75-28 (E2) Always Below 1 Ω
C88-1 (HT1B) or C75-2 (HT1B) - Body ground Always 10 kΩ or higher
C88-3 (OX1B) or C75-25 (OX1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE HEATED OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

6.PERFORM CONFIRMATION DRIVING PATTERN
6.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0137)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0137)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

d.

Input DTCs: P0137.


e.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

Result:
Result Proceed to
ABNORMAL
(P0137 output)
A
NORMAL
(No DTC output)
B




A

B

END