Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P2A00  A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)  


DESCRIPTION

HINT:

Sensor 1 refers to the sensor mounted in front of the Three Way Catalytic Converter (TWC) and located near the engine assembly.


Refer to DTC P2195 (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P2195).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) The calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2 trip detection logic).
·

Air fuel ratio sensor

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.


A250593
2.448,2.156 2.74,0.229 false 2.74,0.229 2.865,0.229 false 1.875,3.052 2.656,3.323 0.781,0.271 10 false Warming up 2.719,3.073 3.938,3.375 1.219,0.302 10 false 20 minutes or more 4.052,3.073 5.354,3.323 1.302,0.25 10 false 10 minutes or more 0.156,2.344 1.323,2.615 1.167,0.271 10 false Ignition Switch ON 0.979,2.073 1.427,2.344 0.448,0.271 10 false Idling 0.198,1.375 1.427,1.646 1.229,0.271 10 false 60 km/h (37 mph) 0.198,0.938 1.427,1.208 1.229,0.271 10 false 64 km/h (40 mph) 0.146,0.438 1.448,0.708 1.302,0.271 10 false 120 km/h (75 mph) 0.479,0.115 1.469,0.354 0.99,0.24 10 false Vehicle Speed 1.656,2.458 1.896,2.667 0.24,0.208 10 false [A] 2.177,1.948 2.542,2.292 0.365,0.344 10 false [B] 3.219,1.063 3.5,1.323 0.281,0.26 10 false [C] 4.729,0.563 5.063,0.854 0.333,0.292 10 false [D] 2.917,0.146 4.635,0.531 1.719,0.385 10 false Engine coolant temperature is 75°C or more

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on [A].

3.

Enter the following menus: Powertrain / Engine and ECT / DTC / Clear.

4.

Clear DTCs.

5.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [B].

6.

Drive the vehicle at 60 km/h (37 mph) or more for 20 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

This step is performed to complete ethanol concentration learning.

·

If DTC P2A00 is output when any of the following conditions is met, it is necessary to complete ethanol concentration learning to meet preconditions.

·

The battery has been disconnected and reconnected.

·

The DTCs have been cleared.

·

Both fuel tank assemblies (main and sub tanks) have been filled with fuel.




7.

Drive the vehicle at a constant speed between 64 km/h and 120 km/h (40 mph and 75 mph) for 10 minutes or more [D].

8.

Turn the ignition switch off.

9.

Repeat steps [B] and [D] above.

10.

Enter the following menus: Powertrain / Engine and ECT / DTC.

11.

Check if any DTCs (any pending DTCs) are output.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Intelligent tester only:

Malfunctioning areas can be identified by performing the "Control the Injection Volume for A/F Sensor" function provided in the Active Test. The "Control the Injection Volume for A/F Sensor" function can help determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.


The following instructions describe how to conduct the "Control the Injection Volume for A/F Sensor" operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the tester on.

4.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

6.

Perform the "Control the Injection Volume for A/F Sensor" operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

7.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.


HINT:
·

The "Control the Injection Volume for A/F Sensor" operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The sensors react in accordance with increases and decreases in the fuel injection volume.



Standard:
Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor (sensor 2) output has a maximum output delay of approximately 20 seconds.


A301859
0.135,0.688 0.75,0.885 0.615,0.198 10 false Case 0.844,0.635 2.906,1.021 2.063,0.385 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.427,0.625 5.573,1 2.146,0.375 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.948,0.635 7.052,1.01 1.104,0.375 10 false Main Suspected Trouble Area 6.427,2.208 6.719,2.479 0.292,0.271 10 false - 0.24,2.198 0.448,2.458 0.208,0.26 10 false 1 0.26,4.292 0.469,4.552 0.208,0.26 10 false 2 0.26,6.344 0.469,6.604 0.208,0.26 10 false 3 0.26,8.396 0.469,8.656 0.208,0.26 10 false 4 1.385,1.594 2,1.792 0.615,0.198 8 false +12.5% 1.417,1.823 2.031,2.021 0.615,0.198 8 false -12.5% 0.583,2.281 1.573,2.5 0.99,0.219 9 false Output Voltage 0.594,1.333 1.75,1.667 1.156,0.333 9 false Injection Volume 0.865,2.646 2.042,2.917 1.177,0.271 8 false Higher than 3.4 V 1.115,2.865 1.906,3.104 0.792,0.24 8 false Below 3.1 V 2.521,2.76 2.823,3.01 0.302,0.25 8 false OK 1.417,3.885 2.031,4.083 0.615,0.198 8 false -12.5% 1.396,3.656 2.01,3.854 0.615,0.198 8 false +12.5% 0.583,3.417 1.75,3.667 1.167,0.25 9 false Injection Volume 0.583,4.333 1.854,4.594 1.271,0.26 9 false Output Voltage 0.875,4.802 1.875,5.01 1,0.208 8 false Almost no reaction 2.552,4.719 2.938,5 0.385,0.281 8 false NG 1.427,5.938 2.042,6.135 0.615,0.198 8 false -12.5% 1.406,5.729 2.021,5.927 0.615,0.198 8 false +12.5% 0.583,5.469 1.677,5.667 1.094,0.198 9 false Injection Volume 0.583,6.417 1.635,6.656 1.052,0.24 9 false Output Voltage 0.865,6.76 1.917,6.917 1.052,0.156 8 false Higher than 3.4 V 1.115,6.979 1.906,7.219 0.792,0.24 8 false Below 3.1 V 2.531,6.865 2.833,7.115 0.302,0.25 8 false OK 0.583,7.5 1.583,7.708 1,0.208 9 false Injection Volume 1.427,8.01 2.042,8.208 0.615,0.198 8 false -12.5% 1.396,7.802 2.01,8 0.615,0.198 8 false +12.5% 0.583,8.438 1.635,8.667 1.052,0.229 9 false Output Voltage 0.865,8.927 1.823,9.125 0.958,0.198 8 false Almost no reaction 2.563,8.854 2.948,9.135 0.385,0.281 8 false NG 3.25,1.333 4.427,1.635 1.177,0.302 9 false Injection Volume 4.021,1.594 4.635,1.792 0.615,0.198 8 false +12.5% 4.042,1.813 4.656,2.01 0.615,0.198 8 false -12.5% 3.25,2.271 4.281,2.5 1.031,0.229 9 false Output Voltage 3.49,2.604 4.667,2.813 1.177,0.208 8 false Higher than 0.55 V 3.813,2.844 4.604,3.083 0.792,0.24 8 false Below 0.4 V 5.198,2.708 5.5,2.958 0.302,0.25 8 false OK 3.25,3.417 4.427,3.604 1.177,0.188 9 false Injection Volume 4.042,3.875 4.656,4.073 0.615,0.198 8 false -12.5% 4.01,3.667 4.625,3.865 0.615,0.198 8 false +12.5% 3.25,4.333 4.396,4.583 1.146,0.25 9 false Output Voltage 3.448,4.698 4.521,4.917 1.073,0.219 8 false Higher than 0.55 V 3.76,4.927 4.594,5.167 0.833,0.24 8 false Below 0.4 V 5.208,4.813 5.51,5.063 0.302,0.25 8 false OK 6.083,3.615 6.906,4.01 0.823,0.396 8 false Air fuel ratio sensor 6.094,4 6.854,4.573 0.76,0.573 8 false Air fuel ratio sensor heater 6.083,4.563 6.844,5.146 0.76,0.583 8 false Air fuel ratio sensor circuit 5.917,3.604 6.083,3.792 0.167,0.188 10 false - 5.917,3.99 6.083,4.177 0.167,0.188 10 false - 5.917,4.542 6.083,4.729 0.167,0.188 10 false - 4.042,5.948 4.656,6.146 0.615,0.198 8 false -12.5% 4.021,5.75 4.635,5.948 0.615,0.198 8 false +12.5% 3.25,5.469 4.354,5.729 1.104,0.26 9 false Injection Volume 3.25,6.417 4.198,6.667 0.948,0.25 9 false Output Voltage 3.5,6.865 4.552,7.052 1.052,0.188 8 false Almost no reaction 5.177,6.781 5.563,7.063 0.385,0.281 8 false NG 3.25,7.5 4.417,7.698 1.167,0.198 9 false Injection Volume 4.031,8 4.646,8.198 0.615,0.198 8 false -12.5% 4.01,7.813 4.625,8.01 0.615,0.198 8 false +12.5% 3.479,8.938 4.521,9.104 1.042,0.167 8 false Almost no reaction 5.156,8.854 5.542,9.135 0.385,0.281 8 false NG 3.26,8.417 4.333,8.667 1.073,0.25 9 false Output Voltage 6.083,5.438 6.927,5.75 0.844,0.313 8 false Heated oxygen sensor 6.073,5.958 6.896,6.333 0.823,0.375 8 false Heated oxygen sensor heater 6.073,6.646 6.917,7.25 0.844,0.604 8 false Heated oxygen sensor circuit 5.917,5.948 6.083,6.135 0.167,0.188 10 false - 5.917,5.417 6.083,5.604 0.167,0.188 10 false - 5.917,6.615 6.083,6.802 0.167,0.188 10 false - 6.083,7.531 6.948,7.906 0.865,0.375 8 false Fuel injector assembly 6.083,7.917 6.833,8.167 0.75,0.25 8 false Fuel pressure 6.094,8.177 6.917,9.281 0.823,1.104 8 false Gas leak from exhaust system (air-fuel ratio extremely rich or lean) 5.917,7.521 6.083,7.708 0.167,0.188 10 false - 5.917,7.906 6.083,8.094 0.167,0.188 10 false - 5.917,8.156 6.083,8.344 0.167,0.188 10 false -

Following the "Control the Injection Volume for A/F Sensor" procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / View / AFS Voltage B1S1 and O2S B1S2.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.



NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read DTCs.

Result:
Result Proceed to
DTC P2A00 is output A
DTC P2A00 and other DTCs are output B


HINT:

If any DTCs relating to the A/F sensor (DTCs for the A/F sensor heater or A/F sensor admittance) are output, troubleshoot those DTCs first.




A

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

B

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C85-2 (+B) - Body ground Ignition switch ON 11 to 14 V



c.

Turn the ignition switch off.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C85-3 (A1A+) - C97-7 (A1A+) Always Below 1 Ω
C85-4 (A1A-) - C97-1 (A1A-) Always Below 1 Ω
C85-1 (HA1A) - C97-6 (HA1A) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C85-3 (A1A+) - C97-7 (A1A+) Always 10 kΩ or higher
C85-4 (A1A-) - C97-1 (A1A-) Always 10 kΩ or higher
C85-1 (HA1A) - C97-6 (HA1A) Always 10 kΩ or higher



f.

Reconnect the ECM connector.


g.

Reconnect the air fuel ratio sensor connector.


Result:
Proceed to
OK
NG



OK

4.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM CONFIRMATION DRIVING PATTERN
Result:
Result
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read DTCs.

Result:
Result Proceed to
DTC P2A00 is output A
DTC is not output B




A

6.REPLACE AIR FUEL RATIO SENSOR

B

6.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.PERFORM CONFIRMATION DRIVING PATTERN
7.PERFORM CONFIRMATION DRIVING PATTERN
Result:
Result
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P2A00 is output B




A

END

B

REPAIR OR REPLACE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO