Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009643 METER / GAUGE / DISPLAY _0052702 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Coolant Temperature Gauge Malfunction  


DESCRIPTION

In this circuit, the meter CPU receives engine coolant temperature signals from the ECM. The meter CPU displays engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E252854
1,1.927 1.365,2.125 0.365,0.198 10 false ECM 5.427,2.229 6.625,2.708 1.198,0.479 10 false Combination Meter Assembly 0.115,2.542 1.052,2.74 0.938,0.198 10 false *1: for 2TR-FE 0.115,3.344 1.073,3.542 0.958,0.198 10 false *3: for 1GR-FE 1.219,1.208 1.688,1.406 0.469,0.198 10 false THWO 1.823,1.208 2.115,1.406 0.292,0.198 10 false G88 5.427,2 5.719,2.198 0.292,0.198 10 false G19 1.813,0.99 2.167,1.188 0.354,0.198 10 false 14*1 2.74,0.979 3.073,1.177 0.333,0.198 10 false 14*3 2.708,1.208 3.083,1.406 0.375,0.198 10 false G154 5.323,1.104 5.458,1.302 0.135,0.198 10 false 4 5.531,1.208 6.031,1.448 0.5,0.24 10 false TEMP 2.302,1.208 2.594,1.406 0.292,0.198 10 false C97 2.292,0.99 2.625,1.188 0.333,0.198 10 false 26*2 0.115,2.948 1.146,3.146 1.031,0.198 10 false *2: for 2TR-FBE 0.125,0.094 1.74,0.417 1.615,0.323 12 false for Gasoline Engine:

E252854
1,1.927 1.365,2.125 0.365,0.198 10 false ECM 5.427,2.156 6.635,2.604 1.208,0.448 10 false Combination Meter Assembly 0.115,2.542 1.833,2.74 1.719,0.198 10 false *1: for 1KD-FTV, 2KD-FTV 0.115,3.344 1.927,3.646 1.813,0.302 10 false *3: for 1KD-FTV (for i-ART) 1.229,1.188 1.688,1.385 0.458,0.198 10 false THWO 1.823,1.208 2.115,1.406 0.292,0.198 10 false G39 5.417,1.979 5.708,2.177 0.292,0.198 10 false G19 1.865,0.99 2.167,1.188 0.302,0.198 10 false 2*1 2.729,0.99 3.042,1.188 0.313,0.198 10 false 16*3 2.719,1.208 3.094,1.406 0.375,0.198 10 false G156 5.323,1.073 5.458,1.271 0.135,0.198 10 false 4 5.542,1.208 6.094,1.51 0.552,0.302 10 false TEMP 2.25,1.208 2.615,1.406 0.365,0.198 10 false G148 2.292,0.99 2.625,1.188 0.333,0.198 10 false 16*2 0.115,2.948 2.427,3.271 2.313,0.323 10 false *2: for 1KD-FTV, 2KD-FTV (for DPF) 0.125,0.104 1.5,0.427 1.375,0.323 12 false for Diesel Engine:

PROCEDURE

1.CHECK ENGINE TYPE
a.

Check the engine type.

Result:
Result Proceed to
for Gasoline Engine A
for Diesel Engine B




A

2.CHECK FOR DTC

B

5.CHECK FOR DTC
2.CHECK FOR DTC

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

NG

GO TO SFI SYSTEM

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the G88*1, C97*2 or G154*3 ECM connector.

*1: for 2TR-FE

*2: for 2TR-FBE

*3: for 1GR-FE



c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G19-4 (TEMP) - G88-14 (THWO) Always Below 1 Ω
G19-4 (TEMP) or G88-14 (THWO) - Body ground Always 10 kΩ or higher


for 2TR-FBE
Tester Connection Condition Specified Condition
G19-4 (TEMP) - C97-26 (THWO) Always Below 1 Ω
G19-4 (TEMP) or C97-26 (THWO) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G19-4 (TEMP) - G154-14 (THWO) Always Below 1 Ω
G19-4 (TEMP) or G154-14 (THWO) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

4.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or normally functioning one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL

OK:

The operation of the engine coolant temperature gauge returns to normal.


Result:
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 2TR-FBE) C
NG (for 1GR-FE) D




A

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

B

C

D

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the G39*1, G148*2 or G156*3 ECM connector.

*1: for 1KD-FTV, 2KD-FTV

*2: for 1KD-FTV, 2KD-FTV (for DPF)

*3: for 1KD-FTV (for i-ART)



c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G19-4 (TEMP) - G39-2 (THWO) Always Below 1 Ω
G19-4 (TEMP) or G39-2 (THWO) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV (for DPF)
Tester Connection Condition Specified Condition
G19-4 (TEMP) - G148-16 (THWO) Always Below 1 Ω
G19-4 (TEMP) or G148-16 (THWO) - Body ground Always 10 kΩ or higher

for 1KD-FTV (for i-ART)
Tester Connection Condition Specified Condition
G19-4 (TEMP) - G156-16 (THWO) Always Below 1 Ω
G19-4 (TEMP) or G156-16 (THWO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or normally functioning one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL

OK:

The operation of the engine coolant temperature gauge returns to normal.


Result:
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 2KD-FTV) C




A

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

B

C