The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU (brake actuator assembly). The speed sensor has a magnet behind its detection terminal, and detects changes in magnetic flux density between the peaks and valleys of the magnetic rotor teeth.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU (brake actuator assembly). The ECU monitors the wheel speeds through these pulse signals to control the brake control system.
When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1271 | Low Output Signal of Front Speed Sensor RH (Test Mode DTC) | Stored during Test Mode. | ·
Front speed sensor RH ·
Front skid control rotor RH ·
Sensor installation |
| C1272 | Low Output Signal of Front Speed Sensor LH (Test Mode DTC) | Stored during Test Mode. | ·
Front speed sensor LH ·
Front skid control rotor LH ·
Sensor installation |
| C1401 | Front Speed Sensor RH Malfunction | One of the following conditions is met:
1.
At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that of the other sensors for 15 seconds or more. 2.
At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. 3.
At a vehicle speed of 10 km/h (6 mph) or more, the outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. |
·
Front speed sensor RH ·
Front skid control rotor RH ·
Sensor installation |
| C1402 | Front Speed Sensor LH Malfunction | One of the following conditions is met:
1.
At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that of the other sensors for 15 seconds or more. 2.
At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. 3.
At a vehicle speed of 10 km/h (6 mph) or more, the outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. |
·
Front speed sensor LH ·
Front skid control rotor LH ·
Sensor installation |
DTCs C1401 and C1271 are for the front speed sensor RH.
DTCs C1402 and C1272 are for the front speed sensor LH.
Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
Turn the ignition switch off.
| *1 | Front Speed Sensor |
| *a | No clearance |
| *b | CORRECT |
| *c | INCORRECT |
Check the speed sensor installation.
There is no clearance between the sensor and the steering knuckle.
The installation bolt is tightened properly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Remove the front speed sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>REMOVAL
Check the speed sensor tip.
No scratches, oil or foreign matter on the sensor tip.
Do not replace the speed sensor if no damage to the speed sensor tip is found.
If the sensor is contaminated with oil or other foreign material, clean the sensor.
If there is iron powder sticking to the rotor, this will result in a malfunction. Therefore, confirm that the rotor is not contaminated with foreign material before replacing the sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Remove the front skid control rotor.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 4WD and Pre-Runner)>REMOVAL
Check the front skid control rotor.
No scratches, oil or foreign matter on the rotor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
Check the speed value output from the speed sensor displayed on the intelligent tester.
Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK
The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Turn the ignition switch off.
Replace the front speed sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B