Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052689 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Engine does not Start  


DESCRIPTION

If the engine does not start and no DTCs are output, there is an open or short circuit between the ECM, transponder key ECU assembly or telephone transceiver assembly (w/ Blocking System).

WIRING DIAGRAM

B315873
5.479,0.917 5.833,1.073 0.354,0.156 10 false EFIO 5.24,0.844 5.438,1 0.198,0.156 10 false 13 5.479,1.396 5.833,1.552 0.354,0.156 10 false EFII 5.948,1.167 6.292,1.323 0.344,0.156 10 false GND 1.49,0.917 1.719,1.073 0.229,0.156 10 false IMI 1.438,1.417 1.802,1.615 0.365,0.198 10 false IMO 1.167,1.979 1.521,2.135 0.354,0.156 10 false ECM 4.823,1.948 5.177,2.104 0.354,0.156 10 false G26 4.823,2.094 6.969,2.302 2.146,0.208 10 false Transponder Key ECU Assembly 0.156,2.458 4.219,2.698 4.063,0.24 10 false *1: for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF) 0.156,2.729 1.115,2.885 0.958,0.156 10 false *2: for 2TR-FE 0.156,3 1.198,3.156 1.042,0.156 10 false *3: for 2TR-FBE 0.156,3.26 2.979,3.417 2.823,0.156 10 false *4: for 1GR-FE 0.156,3.521 3.125,3.729 2.969,0.208 10 false *5: for 1KD-FTV (for DPF), 2KD-FTV (for DPF) 4.688,2.458 6.521,2.667 1.833,0.208 10 false *6: for 1KD-FTV (for i-ART) 1.813,0.927 2.125,1.083 0.313,0.156 10 false G38 1.802,0.719 2.115,0.875 0.313,0.156 10 false 30*1 1.813,1.406 2.125,1.563 0.313,0.156 10 false G38 1.802,1.188 2.115,1.344 0.313,0.156 10 false 29*1 2.208,0.927 2.521,1.083 0.313,0.156 10 false G88 2.198,0.719 2.51,0.875 0.313,0.156 10 false 16*2 2.208,1.406 2.521,1.563 0.313,0.156 10 false G88 2.198,1.188 2.51,1.344 0.313,0.156 10 false 15*2 2.573,0.927 2.938,1.083 0.365,0.156 10 false G146 2.615,0.719 2.927,0.875 0.313,0.156 10 false 31*3 2.573,1.406 2.938,1.563 0.365,0.156 10 false G146 2.615,1.188 2.927,1.344 0.313,0.156 10 false 32*3 2.969,0.927 3.333,1.083 0.365,0.156 10 false G154 3.01,0.719 3.323,0.875 0.313,0.156 10 false 16*4 2.969,1.406 3.333,1.563 0.365,0.156 10 false G154 3.01,1.188 3.323,1.344 0.313,0.156 10 false 15*4 3.365,0.927 3.729,1.083 0.365,0.156 10 false G148 3.406,0.719 3.719,0.875 0.313,0.156 10 false 28*5 3.365,1.406 3.729,1.563 0.365,0.156 10 false G148 3.406,1.188 3.719,1.344 0.313,0.156 10 false 29*5 3.75,0.927 4.115,1.083 0.365,0.156 10 false G156 3.802,0.719 4.115,0.875 0.313,0.156 10 false 28*6 3.75,1.406 4.115,1.563 0.365,0.156 10 false G156 3.802,1.188 4.115,1.344 0.313,0.156 10 false 29*6 5.24,1.313 5.438,1.469 0.198,0.156 10 false 12 6.313,1.083 6.51,1.24 0.198,0.156 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting this symptom, make sure no engine immobiliser system DTCs, SFI system (for 2TR-FE, 2TR-FBE, 1GR-FE) or ECD system (for 1KD-FTV, 2KD-FTV) DTCs are present. If present, troubleshoot the engine immobiliser system DTCs or blocking system DTCs (w/ Blocking System) first.

·

For vehicles with blocking system, refer to "Engine does not Start" (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>Engine does not Start).

·

When replacing the transponder key ECU assembly or ECM, refer to the Service Bulletin.



PROCEDURE

1.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)
a.
B274402
0.688,1.198 1.052,1.521 0.365,0.323 0.771,1.865 1.01,1.865 1.01,1.865 1.292,1.438 true 1.063,2.177 1.354,2.177 1.354,2.177 1.542,1.448 true 0.083,2.396 0.396,2.552 0.313,0.156 10 false *1 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 0.74,1.271 1.198,1.469 0.458,0.198 10 false G26 0.448,1.781 0.906,1.979 0.458,0.198 10 false GND 0.708,2.094 1.323,2.292 0.615,0.198 10 false EFIO 0.271,3.354 0.729,3.552 0.458,0.198 10 false GND
*1 Waveform
*a Component with harness connected(Transponder Key ECU Assembly)


Using an oscilloscope, check the waveform.

Measurement Condition:
Item Content
Tester Connection G26-13 (EFIO) - G26-16 (GND)
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Ignition switch ON


HINT:
·

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

·

Check the waveform when the security indicator light assembly is off (the engine immobiliser system is unset). If the security indicator light assembly does not turn off (the engine immobiliser system cannot be unset), refer to the "Problem Symptoms Table.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>PROBLEM SYMPTOMS TABLE



OK:

Waveform is output normally (refer to illustration).


Result:
Result Proceed to
NG (stuck LOW: 1 V or less) A
NG (stuck HI: 10 V) B
OK C


HINT:

If replacing the ECM, refer to the procedures below.





A

2.REPLACE TRANSPONDER KEY ECU ASSEMBLY

B

REPLACE ECM

C

5.REGISTER ECU COMMUNICATION ID
2.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

3.REGISTER ECU COMMUNICATION ID
3.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.


HINT:

If replacing the ECM, refer to the procedures below.




Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)

NG

REPLACE ECM

5.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.


HINT:

If replacing the ECM, refer to the procedures below.




Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID IS NOT REGISTERED CORRECTLY)

NG

REPLACE ECM