Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052657 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: for Automatic Transmission

*2: for Manual Transmission


WIRING DIAGRAM

E278684
5.448,0.583 5.906,0.781 0.458,0.198 10 false REV 5.25,0.469 5.708,0.667 0.458,0.198 10 false 2 5.313,1.177 5.771,1.375 0.458,0.198 10 false G127 5.313,1.354 6.521,1.802 1.208,0.448 10 false Radio and Display Receiver Assembly 4.042,0.469 4.5,0.667 0.458,0.198 10 false 1 3.75,0.469 4.208,0.667 0.458,0.198 10 false RL 3.094,0.458 3.552,0.656 0.458,0.198 10 false RB 2.917,0.479 3.375,0.677 0.458,0.198 10 false 2 2.833,0.917 4.021,1.094 1.188,0.177 10 false C57 2.833,1.094 4.188,1.531 1.354,0.438 10 false Park/Neutral Position Switch Assembly*1 2.615,2.469 4.333,2.667 1.719,0.198 10 false C27*3, C87*4, C165*5 2.625,2.646 4.792,2.875 2.167,0.229 10 false Back-up Light Switch Assembly*2 0.042,0.594 1.417,1 1.375,0.406 10 false from ECU-IG&GAUGE Fuse 0.083,1.948 2.167,2.167 2.083,0.219 10 false *1: for Automatic Transmission 0.083,2.25 2,2.5 1.917,0.25 10 false *2: for Manual Transmission 2.927,2.063 3.229,2.344 0.302,0.281 10 false 2 4.021,2.063 4.323,2.344 0.302,0.281 10 false 1 0.083,2.604 1.917,2.833 1.833,0.229 10 false *3: for 1KD-FTV (w/o i-ART) 0.083,2.917 1.75,3.083 1.667,0.167 10 false *4: for 2TR-FE, 2TR-FBE 0.083,3.271 1.833,3.5 1.75,0.229 10 false *5: for 1kD-FTV (w/ i-ART)

PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E270655

Enter the "Vehicle Signal Check Mode" screen. (Refer to check Vehicle Signal in Operation Check)

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E140414
1.469,0.5 1.969,0.75 0.5,0.25 0.917,1.354 0.583,0.917 0.583,0.917 0.417,0.917 true 0.135,0.083 0.375,0.25 0.24,0.167 10 false *a 1.552,0.542 2.115,0.708 0.563,0.167 10 false G127 0.115,0.844 0.667,1.073 0.552,0.229 10 false REV
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G127-2 (REV) - Body ground Ignition switch ON, shift lever in R 11 to 14 V
G127-2 (REV) - Body ground Ignition switch ON, shift lever any position other than in R Below 1 V



Result:
Proceed to
OK
NG (for Automatic Transmission)
NG (for Manual Transmission)



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG (for Automatic Transmission)

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG (for Manual Transmission)

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G127 radio and display receiver assembly connector.


b.

Disconnect the C57 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-2 (REV) - C57-1 (RL) Always Below 1 Ω
G127-2 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
E270424
0.115,0.927 0.615,1.167 0.5,0.24 2.292,0.417 2.125,0.417 2.125,0.417 1.792,1 true 2.344,0.333 2.802,0.531 0.458,0.198 10 false RB 0.104,0.083 0.563,0.281 0.458,0.198 10 false *a 0.229,0.979 0.688,1.177 0.458,0.198 10 false C57
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C57-2 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G127 radio and display receiver assembly connector.


b.

Disconnect the C27*1, C87*2 or C165*3 back-up light switch assembly connector.

*1: for 1KD-FTV (w/o i-ART)

*2: for 2TR-FE, 2TR-FBE

*3: for 1KD-FTV (w/ i-ART)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV (w/o i-ART)
Tester Connection Condition Specified Condition
G127-2 (REV) - C27-1 Always Below 1 Ω
G127-2 (REV) - Body ground Always 10 kΩ or higher

for 2TR-FE, 2TR-FBE
Tester Connection Condition Specified Condition
G127-2 (REV) - C87-1 Always Below 1 Ω
G127-2 (REV) - Body ground Always 10 kΩ or higher

for 1KD-FTV (w/ i-ART)
Tester Connection Condition Specified Condition
G127-2 (REV) - C165-1 Always Below 1 Ω
G127-2 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)
a.
E270423
0.073,0.583 0.573,0.833 0.5,0.25 0.083,0.917 0.583,1.167 0.5,0.25 0.083,1.25 0.583,1.5 0.5,0.25 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 0.208,0.635 0.521,0.833 0.313,0.198 10 false C27 0.208,0.958 0.521,1.156 0.313,0.198 10 false C87 0.177,1.302 0.625,1.531 0.448,0.229 10 false C165 0.646,0.615 0.958,0.813 0.313,0.198 10 false *A 0.667,0.948 0.979,1.146 0.313,0.198 10 false *B 0.677,1.292 0.99,1.49 0.313,0.198 10 false *C
*A for 1KD-FTV (w/o i-ART)
*B for 2TR-FE, 2TR-FBE
*C for 1KD-FTV (w/ i-ART)
*a Front view of wire harness connector
(to Back-up Light Switch Assembly)


Disconnect the back-up light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1KF-FTV (w/o i-ART)
Tester Connection Switch Condition Specified Condition
C27-2 - Body ground Ignition switch ON 11 to 14 V

for 2TR-FE, 2TR-FBE
Tester Connection Switch Condition Specified Condition
C87-2 - Body ground Ignition switch ON 11 to 14 V

for 1KF-FTV (w/ i-ART)
Tester Connection Switch Condition Specified Condition
C165-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR