DTC P0171 System Too Lean (Bank 1) |
DTC P0172 System Too Rich (Bank 1) |
| Alcohol Concentration | 22% (E22) | 46% | 75% | 100% (E100) |
| Alcohol Feedback Value | 8% | 24% | 47% | 70.5% |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0171 | With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2-trip detection logic). |
|
| P0172 | With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2-trip detection logic). |
|


| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0171 or P0172 is output | A |
| DTC P0171 or P0172 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections.
|
| ||||
| OK | |
| 3.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage (Click here).
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the Air Fuel Ratio (A/F) sensor and the Heated Oxygen (HO2) sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the intelligent tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (A/F) | +12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2 (HO2) | +12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status AFS B1S1 | Status O2S B1S2 | A/F Condition and A/F Sensor Condition | Misfire | Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - | - | A |
| Lean | Lean | Actual air-fuel ratio lean | May occur |
| A |
| Rich | Rich | Actual air-fuel ratio rich | - |
| |
| Lean | Lean/Rich | A/F sensor malfunction | - |
| B |
| Rich | Lean/Rich | A/F sensor malfunction | - |
|
|
| ||||
| A | |
| 5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
Read Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 8.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leakage.
|
| ||||
| OK | |
| 9.CHECK IGNITION SYSTEM |
Inspect the ignition system (Click here).
|
| ||||
| OK | |
| 10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
Check the fuel injection and volume (Click here).
|
| ||||
|
| ||||
| 11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor (Click here).
|
| ||||
| OK | |
| 12.CHECK AIR FUEL RATIO SENSOR (POWER SOURCE) |
![]() |
Disconnect the air fuel ratio sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A5-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
Reconnect the air fuel ratio sensor connector.
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A5-1 (HA1A) - E22-6 (HA1A) | Always | Below 1 Ω |
| A5-3 (A1A+) - E22-7 (A1A+) | Always | Below 1 Ω |
| A5-4 (A1A-) - E22-1 (A1A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A5-1 (HA1A) or E22-6 (HA1A) - Body ground | Always | 10 kΩ or higher |
| A5-3 (A1A+) or E22-7 (A1A+) - Body ground | Always | 10 kΩ or higher |
| A5-4 (A1A-) or E22-1 (A1A-) - Body ground | Always | 10 kΩ or higher |
Reconnect the air fuel ratio sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0171 or P0172 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 16.CHECK HARNESS AND CONNECTOR |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0171 or P0172 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A4-3 (VG) - E20-13 (VG) | Always | Below 1 Ω |
| A4-2 (E2G) - E20-7 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A4-3 (VG) or E20-13 (VG) - Body ground | Always | 10 kΩ or higher |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 19.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0171 or P0172 is output | B |
|
| ||||
| A | ||
| ||
| 21.CHECK HARNESS AND CONNECTOR (A/F SENSOR - A/F RELAY, A/F RELAY - INTEGRATION RELAY) |
Disconnect the air fuel ratio sensor connector.
Remove the A/F relay from the engine room relay block.
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A5-2 (+B) - A/F relay terminal (3) | Always | Below 1 Ω |
| A/F relay terminal (5) - 1H-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A5-2 (+B) or A/F relay terminal (3) - Body ground | Always | 10 kΩ or higher |
| A/F relay terminal (5) or 1H-1 - Body ground | Always | 10 kΩ or higher |
Reconnect the air fuel ratio sensor connector.
Reinstall the integration relay.
Reinstall the A/F relay.
|
| ||||
| OK | |
| 22.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY (A/F) |
![]() |
Inspect the A/F relay.
Remove the A/F relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Always | 10 kΩ or higher |
| 3 - 5 | Always | Below 1 Ω (when battery voltage is applied to terminals 1 and 2) |
|
| ||||
| OK | ||
| ||