DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0300 | Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2 trip detection logic):
|
|
| P0301 P0302 P0303 P0304 | Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
|
| Required Sensors/Components (Main) | Crankshaft position sensor and camshaft position sensor |
| Required Sensors/Components (Related) | Engine coolant temperature, intake air temperature sensors and mass air flow meter |
| Frequency of Operation | Continuous |
| Intake air temperature | Higher than -10°C (14°F) |
| Either of following conditions (a) or (b) met | - |
| (a) Engine coolant temperature at engine start | Higher than -7°C (19°F) |
| (b) Engine coolant temperature | Higher than 20°C (68°F) |
| Duration | 1000 crankshaft revolutions x 4 |
| Duration | 200 crankshaft revolutions x 3 |


| Engine Speed | Duration |
| Idling | 8.0 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0300, P0301, P0302, P0303 and/or P0304 is output | A |
| P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
| NEXT | |
| 4.READ VALUE USING INTELLIGENT TESTER (MISFIRE COUNT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count, #2, #3 and #4.
Allow the engine to idle.
Read the values for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the intelligent tester. If no misfire counts occur in any cylinders, perform the following procedures:
Check Cylinder #1 Misfire Count to Cylinder #4 Misfire Count.
If misfire counts are still not displayed, perform procedures "A" and "B", and then check the misfire counts again.
Procedure A: Drive the vehicle while matching the vehicle conditions to the Misfire RPM and Misfire Load values noted in the "Read Value Using Intelligent Tester (Misfire RPM and Misfire Load)" procedure above.
Procedure B: Read Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or the DTCs output on the intelligent tester.
| Result | Proceed to |
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
|
| ||||
| A | |
| 5.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 6.CHECK FOR SPARK (SPARK TEST) |
Perform a spark test .
| NEXT | |
| 7.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 8.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the F4, F5, F6 and F7 injector connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F4-1 - Body ground | Ignition switch ON | 11 to 14 V |
| F5-1 - Body ground | Ignition switch ON | 11 to 14 V |
| F6-1 - Body ground | Ignition switch ON | 11 to 14 V |
| F7-1 - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM) |
Disconnect the F4, F5, F6 and F7 injector connectors.
Disconnect the E10 ECM connector
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F4-2 - E10-6 (#10) | Always | Below 1 Ω |
| F5-2 - E10-5 (#20) | Always | Below 1 Ω |
| F6-2 - E10-2 (#30) | Always | Below 1 Ω |
| F7-2 - E10-1 (#40) | Always | Below 1 Ω |
| F4-2 or E10-6 (#10) - Body ground | Always | 10 kΩ or higher |
| F5-2 or E10-5 (#20) - Body ground | Always | 10 kΩ or higher |
| F6-2 or E10-2 (#30) - Body ground | Always | 10 kΩ or higher |
| F7-2 or E10-1 (#40) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).
|
| ||||
| OK | |
| 11.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
|
| ||||
| OK | |
| 12.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 13.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 14.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 2500 rpm.
|
| ||||
| OK | |
| 15.CHECK VALVE TIMING |
![]() |
Remove the cylinder head cover.
Turn the crankshaft to align the timing marks of the crankshaft.
Align the groove of the crankshaft pulley with the "0" position.
Confirm whether the timing marks of the camshaft pulley and cylinder head cover are facing each other.
If the timing marks are not facing each other, turn the crankshaft clockwise 360°. Confirm again if the timing marks are facing each other.
|
| ||||
|
| ||||
| 16.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
|
| ||||
| OK | |
| 17.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 18.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 19.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 2500 rpm.
|
| ||||
| OK | |
| 20.CHECK VALVE TIMING |
![]() |
Remove the cylinder head cover.
Turn the crankshaft to align the timing marks of the crankshaft.
Align the groove of the crankshaft pulley with the "0" position.
Confirm whether the timing marks of the camshaft pulley and cylinder head cover are facing each other.
If the timing marks are not facing each other, turn the crankshaft clockwise 360°. Confirm again if the timing marks are facing each other.
|
| ||||
| OK | |
| 21.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 22.CHECK FOR SPARK (SPARK TEST) |
Perform a spark test .
| NEXT | |
| 23.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 24.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the F4, F5, F6 and F7 injector connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F4-1 - Body ground | Ignition switch ON | 11 to 14 V |
| F5-1 - Body ground | Ignition switch ON | 11 to 14 V |
| F6-1 - Body ground | Ignition switch ON | 11 to 14 V |
| F7-1 - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 25.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM) |
Disconnect the F4, F5, F6 and F7 injector connectors.
Disconnect the E10 ECM connector
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F4-2 - E10-6 (#10) | Always | Below 1 Ω |
| F5-2 - E10-5 (#20) | Always | Below 1 Ω |
| F6-2 - E10-2 (#30) | Always | Below 1 Ω |
| F7-2 - E10-1 (#40) | Always | Below 1 Ω |
| F4-2 or E10-6 (#10) - Body ground | Always | 10 kΩ or higher |
| F5-2 or E10-5 (#20) - Body ground | Always | 10 kΩ or higher |
| F6-2 or E10-2 (#30) - Body ground | Always | 10 kΩ or higher |
| F7-2 or E10-1 (#40) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 26.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).
|
| ||||
| OK | |
| 27.CHECK HARNESS AND CONNECTOR |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).
| NEXT | |
| 28.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (P0300, P0301, P0302, P0303 or P0304 is output) | A |
| NORMAL (No DTC is output) | B |
|
| ||||
| A | |
| 29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A4-3 (VG) - E10-28 (VG) | Always | Below 1 Ω |
| A4-2 (E2G) - E10-30 (E2G) | Always | Below 1 Ω |
| A4-3 (VG) or E10-28 (VG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 30.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (No DTC is output) | A |
| ABNORMAL (P0300, P0301, P0302, P0303 or P0304 is output) | B |
|
| ||||
| A | ||
| ||
| 32.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||