DTC C1413 Front Speed Sensor RH Output Malfunction |
DTC C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1414 Front Speed Sensor LH Output Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1413 C1414 | One of the following conditions is met:
|
|
| C1275 C1276 | Stored during Test Mode. |
|
| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Speed Open | Front speed sensor RH open circuit detection / Error or Normal | Normal | - |
| FL Speed Open | Front speed sensor LH open circuit detection / Error or Normal | Normal | - |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | Front speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
Check the speed value output from the speed sensor displayed on the intelligent tester.
|
| ||||
| OK | |
| 3.PERFORM TEST MODE (SIGNAL CHECK) |
Perform the signal check in the Test Mode procedure (Click here).
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK FRONT SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
![]() |
Check the speed sensor installation (Click here).
| *1 | Front Speed Sensor |
| *a | No clearance |
| *b | CORRECT |
| *c | INCORRECT |
|
| ||||
| OK | |
| 6.INSPECT FRONT SPEED SENSOR TIP |
Turn the ignition switch off.
Remove the front speed sensor (Click here).
Check the speed sensor tip.
|
| ||||
| OK | |
| 7.INSPECT FRONT SKID CONTROL ROTOR |
Turn the ignition switch off.
Remove the front skid control rotor (Click here).
Check the front skid control rotor.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-7 (FR+) - S5-1 (FR+) | Always | Below 1 Ω |
| S25-7 (FR+) - Body ground | Always | 10 kΩ or higher |
| S25-6 (FR-) - S5-2 (FR-) | Always | Below 1 Ω |
| S25-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| S25-19 (FL+) - S4-1 (FL+) | Always | Below 1 Ω |
| S25-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| S25-18 (FL-) - S4-2 (FL-) | Always | Below 1 Ω |
| S25-18 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK TERMINAL VOLTAGE (FR+, FL+ TERMINAL) |
Turn the ignition switch off.
Connect the skid control ECU (brake actuator assembly) connector.
Disconnect the front speed sensor connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S5-1 (FR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| S4-1 (FL+) - Body ground | Ignition switch ON | 8 to 14 V |
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector (to Front Speed Sensor) |
|
| ||||
| OK | |
| 10.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||
| 11.REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
| NEXT | |
| 12.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||