Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1422    Master Cylinder Pressure Sensor Zero Point High Malfunction

for Preparation Click here


DESCRIPTION

Refer to DTCs C1421, C1423 and C1424 .

DTC Code
DTC Detection Condition
Trouble Area
C1422
When the stop light switch is off, the PMC terminal voltage is higher than 0.86 V for 5 seconds or more.
  1. STOP fuse
  2. Stop light switch assembly
  3. Stop light switch circuit
  4. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM


C237300E06


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. Before disconnecting the connector, make sure that there are no problems with the connection.
  4. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.

1.CHECK DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC C1422 is output
    A
    DTC C1422 and C1425 are output
    B



B
GO TO DTC C1425 (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch display observed on the intelligent tester changes according to the brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 5
OK


3.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
  1. Turn the ignition switch off.

  1. Check the brake pedal height and stop light switch installation (Click here).

    OK:
    The brake pedal height and stop light switch installation are normal.



NG
ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH (Click here)
OK


4.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC C1422 is not output
    A
    DTC C1422 is output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK TERMINAL VOLTAGE (STOP LIGHT POWER SOURCE CIRCUIT)
  1. Turn the ignition switch off.

  1. Disconnect the stop light switch assembly connector.



    C237276E06
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S14-2 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Turn the ignition switch off.

  1. Remove the stop light switch assembly (Click here).

  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


7.CHECK TERMINAL VOLTAGE (STP TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.



    C199357E75
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S25-2 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Brake Actuator Assembly])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)