Home › ENGINE ยท 2TR-FBE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT ENGINE MOUNTING BRACKET LH
  1. Install the mounting bracket with the 4 bolts.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



2. INSTALL FRONT ENGINE MOUNTING BRACKET RH
  1. Install the mounting bracket with the 4 bolts.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



3. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Install a new O-ring to the oil control valve.

  1. Apply a light coat of engine oil to the O-ring.

  1. Install the oil control valve with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the oil control valve connector.



4. INSTALL CRANKSHAFT POSITION SENSOR
  1. Apply a light coat of engine oil to the O-ring of the sensor.

  1. Install the sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Make sure that the O-ring is not cracked or jammed when installing.

  1. Install the connector to the connector bracket.

  1. Attach the harness clamp.

  1. Connect the sensor connector.



5. INSTALL CAMSHAFT POSITION SENSOR
  1. Apply a light coat of engine oil to the O-ring of the sensor.

  1. Install the sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Make sure that the O-ring is not cracked or jammed when installing.

  1. Connect the sensor connector.



6. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
  1. Install a new gasket to the sensor.

  1. Install the sensor.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }

  1. Connect the sensor connector.



7. INSTALL KNOCK SENSOR


    A099415E02
  1. Install the sensor so that it is horizontal as shown in the illustration. Then install the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    The acceptable installation angle of the sensor is between 10° upward and downward from the horizontal position.

  1. Connect the sensor connector.



8. INSTALL NO. 1 WATER BY-PASS PIPE
  1. Install the end plate with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the No. 1 water by-pass pipe from the rear end plate with the bolt.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }



9. INSTALL HEATER WATER INLET HOSE


10. INSTALL HEATER WATER OUTLET HOSE


11. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY


    G036762E02
  1. Apply adhesive to 2 or 3 threads of the oil pressure switch.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the oil pressure switch.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installation of the switch.

  1. Connect the oil pressure switch connector.

  1. Start the engine and check for engine oil leaks.



12. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A110368E03
  1. Install the spacer and pulley with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



13. INSTALL THERMOSTAT


    A110369E02
  1. Install a new gasket to the thermostat.

    HINT:
    When installing the thermostat to the gasket, be careful not to deform the gasket. Make sure that the thermostat is properly installed into the groove of the gasket, as shown in the illustration.

  1. Insert the thermostat with the jiggle valve upward.

    HINT:
    The jiggle valve may be set within 10° of either side of the prescribed position.



14. INSTALL WATER INLET
  1. Install a new gasket and the water inlet with the 2 nuts and bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the power steering pump connector.



15. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


A099636E01
  1. Temporarily install the belt tensioner with the 3 bolts.

    HINT:
    Make sure the flanges of the bolts are contacting the tensioner surface.

  1. Install the tensioner with the 3 bolts.

    Torque:
    for bolt A:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    for bolt B:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }
    for bolt C:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



16. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

NOTICE:
Install the No. 1 compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the drive belt.



    A330624
  1. Temporarily install the No. 1 compressor mounting bracket with the 3 bolts.

    HINT:
    Temporarily install the No. 1 compressor mounting bracket with the 3 bolts so that the bracket can be moved by hand.



  1. Push the No. 1 compressor mounting bracket toward the cylinder block as shown in the illustration and tighten bolt B.


    A332516E01

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf } for bolt B

    HINT:
    Make sure there is no clearance between the cylinder block and No. 1 compressor mounting bracket as shown in the illustration.



    A332517E01
  1. Uniformly tighten the 4 bolts in the order shown in the illustration.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf } for bolt A
    24.5 N*m{ 250 kgf*cm , 18 ft.*lbf } for bolt C



17. INSTALL IDLE PULLEY ASSEMBLY
  1. Temporarily install the idle pulley assembly with the bolt.

    NOTICE:
    Do not use any tools.

  1. Tighten the bolt.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



18. INSTALL EXHAUST MANIFOLD
  1. Install a new gasket.



    A250369E01
  1. Install the exhaust manifold with 8 new nuts in the order shown in the illustration.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



19. INSTALL AIR SWITCHING VALVE ASSEMBLY
  1. Install the air switching valve assembly with 2 new nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the air switching valve connector.



20. INSTALL NO. 4 INTAKE PIPE


    A253116E01
  1. Install 2 new gaskets and the No. 4 intake pipe with 4 new nuts in the order shown in the illustration. Tighten the nuts labeled 1 and 3 to the torque specification again.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Check that the nuts are tightened to the torque specification.



21. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the heat insulator with the 5 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



22. INSTALL INTAKE MANIFOLD
  1. Install a new gasket and the intake manifold with the 5 bolts and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the crankshaft position sensor to the clamp.



23. INSTALL FUEL INJECTOR ASSEMBLY


    A099091E02
  1. Install a new insulator to the fuel injector.

  1. Apply a light coat of grease or gasoline to a new O-ring and install it to the fuel injector.



    A087155E01
  1. Apply a light coat of grease or gasoline on the place where the delivery pipe touches the O-ring.

  1. To install the fuel injector into the fuel delivery pipe, push the fuel injector while twisting it back and forth.

    NOTICE:
    1. Be careful not to twist the O-ring.
    2. After installing the fuel injector, check that it turns smoothly. If not, reinstall it with a new O-ring.

  1. Position the fuel injector connector so that it faces downward.



24. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
  1. Apply a light coat of gasoline or spindle oil to new O-rings, and then install one to each spacer.



    A312424
  1. Install the 4 spacers to the cylinder head.

  1. Install 4 new injector vibration insulators to the cylinder head.

  1. Install the 2 No. 1 delivery pipe spacers to the cylinder head.

  1. Install the fuel delivery pipe together with the 4 fuel injectors with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not drop the fuel injectors when installing the fuel delivery pipe.

  1. Connect the 4 injector connectors.

  1. Connect the 4 clamps and wire harness to the delivery pipe.

  1. Connect the vacuum hose.



25. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY


    A306999E02
  1. Install a new gasket on the intake manifold.

    HINT:
    Align the protrusion of the gasket with the groove of the intake manifold.

  1. Install the throttle body with motor with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 2 water by-pass hoses to the throttle body with motor.

  1. Connect the throttle position sensor and control motor connector.



26. INSTALL ENGINE WIRE


    G038850E02
  1. Connect the wire harness (engine ground wire) to the engine rear side with the 2 bolts so that it is within the specified range shown in the illustration.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

  1. Connect the oil pressure sensor connector.

  1. Connect the noise filter connector.

  1. Connect the camshaft position sensor connector.

  1. Connect the 4 injector connectors.

  1. Connect the crankshaft position sensor connector.

  1. Connect the oil control valve connector.

  1. Connect the purge VSV connector.

  1. Connect the throttle body connector.

  1. Connect the engine coolant temperature sensor connector.

  1. Connect the knock sensor connector.

  1. Connect the wire harness to the clamps.



27. INSTALL GENERATOR ASSEMBLY
  1. Install the generator with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Connect the generator connector.

  1. Install the generator wire with the bolt and nut.

    Torque:
    for nut:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
    for bolt:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Attach the terminal cap.



28. INSTALL PCV PIPE
  1. Install the PCV pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



29. INSTALL SPARK PLUG
  1. Using a 16 mm plug wrench, install the 4 spark plugs.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



30. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 4 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the ignition coil connector.



31. REMOVE ENGINE FROM ENGINE STAND
  1. Attach an engine sling device and hang the engine with a chain block.

    NOTICE:
    Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

  1. Lift the engine and remove it from the engine stand.

    NOTICE:
    With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

  1. Place the engine onto a work bench.



32. INSTALL ENGINE ASSEMBLY


    A117894E02
  1. Attach the engine sling device and chain block to the engine hangers.

  1. Slowly lower the engine assembly into the engine compartment.

  1. Install the engine mounting brackets with the 4 bolts and 4 nuts.

    Torque:
    38 N*m{ 388 kgf*cm , 28 ft.*lbf }



33. INSTALL REAR END PLATE
  1. Install the end plate with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



34. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

HINT:
  1. The mounting bolts are tightened in 2 progressive steps.
  2. If any of the mounting bolts is broken or deformed, replace it.

  1. Apply adhesive to 2 or 3 threads of the mounting bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the flywheel.



    A099210E02
  1. Fix the crankshaft in place with SST.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    G035062E02
  1. Install and uniformly tighten the 10 mounting bolts in several passes in the order shown in the illustration.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }

    If any of the mounting bolts does not meet the torque specification, replace the mounting bolts.



    G035063E01
  1. Mark the mounting bolts with paint.

  1. Retighten the mounting bolts by 90° in the numerical order shown in the illustration.



    G035062E02
  1. Check that the painted marks are now at a 90° angle to the position.



35. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

HINT:
  1. The mounting bolts are tightened in 2 progressive steps.
  2. If any of the mounting bolts is broken or deformed, replace it.



    A099210E02
  1. Fix the crankshaft in place with SST.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Install the front drive plate spacer, drive plate and rear drive plate spacer to the crankshaft.

  1. Clean the bolts and bolt holes.

  1. Apply adhesive to 2 or 3 threads of the mounting bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    A099868E04
  1. Install and uniformly tighten the 10 mounting bolts in several passes in the order shown in the illustration.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    If any of the mounting bolts does not meet the torque specification, replace the mounting bolts.



36. INSPECT DRIVE PLATE (for Automatic Transmission)
  1. Check the drive plate for damage.



    C191483E01
  1. Set up a dial indicator and measure the runout of the 6 portions around the torque converter fitting surfaces.

    Maximum runout:
    0.20 mm (0.0079 in.)

    If the runout is more than the maximum or if the ring gear is damaged, replace the drive plate .



37. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)


    C226320
  1. Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel.

    SST
    09301-00110  

    NOTICE:
    Make sure not to insert the clutch disc facing the wrong direction.



38. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)


    D029623E03
  1. Align the matchmarks on the clutch cover and flywheel.

  1. Tighten the 6 bolts as described below.

    1. Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.

    2. Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.

      Torque:
      19 N*m{ 195 kgf*cm , 14 ft.*lbf }

  1. Lightly move SST up and down, and right and left.

    SST
    09301-00110  

  1. Check that the disc is in the center, and then tighten the bolts.



39. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)


    D029624E01
  1. Using a dial indicator with roller instrument, measure the diaphragm spring tip alignment.

    Maximum misalignment:
    0.5 mm (0.020 in.)


    1. D029625E03
      If the misalignment is greater than the maximum, use SST to adjust the diaphragm spring tip alignment.
    SST
    09333-00013  



40. INSTALL MANUAL TRANSMISSION UNIT (for Manual Transmission)
(Click here)


41. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)


42. INSTALL STARTER ASSEMBLY
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Install the starter wire to terminal 30 with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the terminal cap.

  1. Connect the starter connector.



43. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY


C098710E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft to the extension housing.

  1. Temporarily install the center support bearing with the 2 plates and 2 bolts. Tighten the bolts as much as possible by hand.



    C119752E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Connect the propeller shaft with the 4 washers, 4 bolts and 4 nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



    C118622E02
  1. Unload the vehicle. Adjust the bearing so that the center line of the center bearing and center bearing housing (see illustration) are within 0 +/-1 mm (0 +/-0.0394 in.) of each other. Measure the difference along the vehicle front/rear axis.

  1. Tighten the 2 bolts of the center support bearing.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



44. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A107610
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40 mm (1.57 in.)

    If the length is less than the minimum, replace the compression spring.

  1. Install the front pipe to the pipe support.



    A099436E03
  1. Install a new gasket to the exhaust manifold.

    NOTICE:
    1. Make sure the gasket is facing the correct direction.
    2. Do not reuse the gasket.
    3. To ensure a proper seal, do not use the front pipe to force the gasket onto the exhaust manifold.

    HINT:
    Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.

  1. Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



45. INSTALL HOOD ASSEMBLY
  1. Install the hood with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the washer nozzle hose.

  1. Adjust the hood (Click here).



46. INSTALL COOLER COMPRESSOR ASSEMBLY


G039332E02
  1. Temporarily install the compressor with the bolt labeled A.

  1. Install the compressor completely by tightening the 4 bolts in the order shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    NOTICE:
    In order to prevent misalignment, which causes belt rattle, tightening of the bolts must be performed in the order shown.

  1. Connect the compressor connector.

  1. Install the suction hose with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



47. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Install a new O-ring and the dipstick guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



48. INSTALL ENGINE OIL LEVEL DIPSTICK


49. INSTALL VANE PUMP ASSEMBLY
  1. Install the vane pump with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the oil pressure switch connector.



50. CONNECT ENGINE WIRE
  1. Connect the wire clamp to the engine mounting bracket front LH with the bolt.

    Torque:
    13 N*m{ 128 kgf*cm , 9 ft.*lbf }

  1. Connect the 2 engine room junction block connectors and connect the wire clamp.

  1. Connect the cable to the engine room junction block with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Install the engine room relay block cover (side).

  1. Install the engine room relay block cover (upper).

  1. Connect the ground wire with the nut.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



    A173606E01
  1. Connect the ground wire to the frame with the bolt so that it is within the range shown in the illustration.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

  1. Connect the sensor bracket to the right side of the frame with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.



    A266908E01
  1. Push the engine wire through the dash panel into the cabin.

    HINT:
    The wire should be within the range shown in the illustration.

  1. Connect the air injection driver connector.

  1. Connect the ECM connectors.

    1. Connect the 4 ECM connectors.

    2. Install the glove compartment door.



51. CONNECT FUEL HOSE
  1. Connect the fuel hose.



52. CONNECT NO. 2 FUEL HOSE
  1. Connect the No. 2 fuel hose.



53. CONNECT NO. 1 FUEL HOSE
  1. Connect the No. 1 fuel hose (Click here).



54. CONNECT HOSE
  1. Connect the vacuum hose (for brake master cylinder).

  1. Connect the hose to the purge VSV.



55. CONNECT HEATER WATER HOSE
  1. Connect the heater water inlet hose and heater water outlet hose to the heater pipe.



56. INSTALL RADIATOR ASSEMBLY
  1. Install the radiator with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Attach the 4 clamps to the radiator side.

  1. w/ Airbag System:

    1. Attach the 4 clamps to the radiator.



57. CONNECT OIL COOLER INLET HOSE (for Automatic Transmission)
  1. Connect the oil cooler inlet hose to the radiator.



58. CONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)
  1. Connect the oil cooler outlet hose to the radiator.



59. INSTALL FAN PULLEY


60. INSTALL FAN SHROUD


A099679E03
  1. Install the fan pulley to the engine water pump.

  1. Place the shroud together with the fluid coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Install the coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.

  1. Attach the shroud's claws to the radiator as shown in A in the illustration.

  1. Install the fan shroud with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the reservoir hose to the radiator tank upper.

  1. Install the drive belt (Click here).

  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



61. INSTALL AIR PUMP INLET
  1. Connect the air pump inlet to the radiator with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



62. INSTALL DRIVE BELT


    A097752E07
  1. Install the drive belt to the pulleys except the V-ribbed belt tensioner pulley.

  1. Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and then install the drive belt to the tensioner pulley.

    NOTICE:
    1. The backside of the drive belt should face the tensioner pulley.
    2. Check that the drive belt is properly set to each pulley.



    G038479E02
  1. After a new belt has been installed, check that the tensioner indicator mark is within range A shown in the illustration.



63. CONNECT RADIATOR HOSE OUTLET
  1. Connect the radiator hose outlet to the radiator.



64. CONNECT RADIATOR HOSE INLET
  1. Connect the radiator hose inlet to the radiator.



65. INSTALL RADIATOR GRILLE
  1. Attach the 6 claws to install the radiator grille.

  1. Install the 2 screws and 2 clips.



66. INSTALL INTAKE AIR CONNECTOR AND AIR CLEANER ASSEMBLY
  1. Install the air cleaner and intake air connector assembly with the 4 bolts, and tighten the hose clamp.

    Torque:
    for air cleaner:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }
    for intake air connector:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    for hose clamp:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the mass air flow meter connector and harness clamps.

  1. Connect the No. 2 PCV hose.

  1. Connect the vacuum hose.



67. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



68. ADD ENGINE OIL
  1. Add fresh engine oil.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource- Conserving" or ILSAC multigrade engine oil
    1. 5W-30
    2. 10W-30
    (5W-30 is the best choice for good fuel economy and good starting in cold weather)
    API grade SL, SM or SN multigrade engine oil
    1. 15W-40
    2. 20W-50

    Standard Capacity:
    Item
    Capacity
    Drain and refill without oil filter change
    5.3 liters (5.6 US qts, 4.7 Imp. qts)
    Drain and refill with oil filter change
    5.6 liters (5.9 US qts, 4.9 Imp. qts)
    Dry fill
    6.3 liters (6.7 US qts, 5.5 Imp. qts)

  1. Install the oil filler cap.



69. ADD ENGINE COOLANT
  1. Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Torque:
    for Cylinder block drain cock plug:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

    Standard Capacity:
    Item
    Specified Condition
    A/T
    8.1 liters (8.6 US qts, 7.1 Imp. qts)
    M/T
    7.8 liters (8.2 US qts, 6.9 Imp. qts)

    NOTICE:
    Never use water as a substitute for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

  1. Fill the radiator reservoir with TOYOTA SLLC to the F line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the F line, add TOYOTA SLLC to the F line.

  1. Install the radiator cap.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens.
      While the thermostat is open, circulate the coolant for several minutes.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Check the coolant level in the radiator reservoir.
    If the coolant level is below the L line, add SLLC up to the reservoir F line.



70. ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Fluid type:
Toyota Genuine ATF Type T-IV



71. INSPECT AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
  1. Inspect the automatic transmission fluid (Click here).



72. ADD MANUAL TRANSMISSION OIL (for Manual Transmission)


D025304E06

Oil grade:
GL-4

Viscosity:
SAE 75W-90

Standard capacity:
2.6 liters (2.7 US qts, 2.3 Imp. qts)

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }



73. INSPECT FOR FUEL LEAK (for Fuel Main Tank)
  1. Connect the intelligent tester to the DLC3.

    1. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    2. Push the intelligent tester main switch on.

    3. Select the Active Test and enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check for fuel leaks.

    1. Check that there are no fuel leaks after performing maintenance anywhere on the fuel system.
      If there are fuel leaks, repair or replace parts as necessary.



74. INSPECT FOR FUEL LEAK (for Fuel Sub Tank)
  1. Start the engine.

    NOTICE:
    Perform the inspection while the engine is cold.
    The fuel pump operates only for a certain amount of time when the coolant temperature is 20°C (68°F) or less and the learned ethanol concentration is 85% or more.

  1. Check for fuel leaks.

    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



75. INSPECT FOR OIL LEAK
  1. Start the engine, and check that there are no oil leaks after performing maintenance.



76. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the cylinder block and cylinder head.



77. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



78. INSTALL NO. 1 ENGINE UNDER COVER


79. INSPECT IGNITION TIMING
  1. Warm up the engine and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.

  1. When using the intelligent tester:
    Check the ignition timing.

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine at idle.

    3. Turn the intelligent tester main switch on.

    4. Enter the following item: Powertrain / Engine and ECT / Data List / IGN Advance.

      Standard ignition timing:
      0 to 20° BTDC @ idle

      HINT:
      Please refer to the intelligent tester operator's manual for further details.



    G039759E02
  1. When not using the intelligent tester:
    Check the ignition timing.

    1. Using SST, connect tachometer probe to terminal TAC of the DLC3.

      SST
      09843-18030  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the engine.
      2. Turn off all electrical systems before connecting the terminals.

    2. Clamp the tester probe of a timing light to the 4 lead wires or green-red lead wire of the ignition coil connector for No. 1 cylinder.

    3. Start the engine.



    4. G039758E02
    5. Using SST, connect terminals TC and CG of the DLC3.

      SST
      09843-18040  

      NOTICE:
      When checking the ignition timing, the transmission should be in the neutral position.

      HINT:

      1. A099876E06
      2. After connecting terminals (TC and CG), engine rpm changes to approximately 1000 to 1500 rpm for 5 seconds, then returns to idle speed. Because the ECM checks that the ISC (idle speed control system) operates properly.
      3. Perform the inspection of the ignition timing after engine rpm is returned to idle speed.

    6. Using a timing light, measure the ignition timing.

      Standard ignition timing:
      3 to 7° BTDC @ idle

    7. Remove the SST from terminals 13 (TC) and 4 (CG) of the DLC3.

    8. Check the ignition timing.

      Standard ignition timing:
      0 to 20° BTDC @ idle

    9. Confirm that ignition timing moves to the advanced angle side when the engine speed is increased.

    10. Remove the timing light.



80. INSPECT IDLE SPEED
  1. Warm up and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.



  1. Check the idle speed control system.



      G039758E02
    1. Using SST, connect terminals TC and CG of the DLC3.

      SST
      09843-18040  

    2. Start the engine at idle.

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the engine.
      2. Turn off all electrical systems before connecting the terminals.
      3. When checking ISC function, the transmission should be in the neutral position.



    3. A099876E06
    4. After connecting terminals (TC and CG), check that the engine speed changes to approximately 1000 to 1500 rpm for 5 seconds, and then returns to idle speed.
      If the result is not as specified, check the throttle body, DTC (Click here) and wire harness.



81. CHECK CO/HC
  1. Start and warm up the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds and idle the engine.

  1. Insert CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe.

  1. Check CO/HC concentration at idle.

    Standard idle CO concentration:
    0 to 0.5 %

    Standard idle HC concentration:
    Applicable local regulation

  1. If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.

    1. Check the air fuel ratio sensor (Click here) and heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, and then inspect and repair the applicable causes if necessary.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Plugs are contaminated, shorted or gaps are defective
      2. Incorrect valve clearance
      3. Leaks in intake and exhaust valves
      4. Leaks in cylinders
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective ECT sensor
        3. Defective Mass Air Flow (MAF) meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor



82. CHECK FUNCTION OF THROTTLE BODY
  1. Check the throttle control motor operating sound.

    1. Turn the ignition switch to ON.

    2. When depressing the accelerator pedal, check the operating sound of the running motor. Make sure that no friction noises are emitted from the motor. If friction noise exists, replace the throttle body.

  1. Check the throttle position sensor.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Sensor Position.

      Standard throttle valve opening percentage:
      60% or more

      NOTICE:
      When checking the standard throttle valve opening percentage, make sure the transmission is in neutral.

      If the result is not as specified, check the throttle body with motor, the wire harness and the ECM.