ENGINE ASSEMBLY > INSTALLATION |
| 1. INSTALL FRONT ENGINE MOUNTING INSULATOR |
Install the 2 front engine mounting insulators with the 2 nuts.
| 2. INSTALL ENGINE WIRE |
Install the engine wire to the engine.
| 3. INSTALL ENGINE HANGERS |
![]() |
Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 engine hanger | 12284-30020 |
| No. 2 engine hanger | 12282-67030 |
| Bolt | 90105-T0164 or 91552- 81014 and 90119-T0065 or 91642-81030 |
| 4. REMOVE ENGINE FROM ENGINE STAND |
Attach an engine sling device and hang the engine with a chain block.
Remove the engine from the engine stand.
| 5. INSTALL ENGINE ASSEMBLY |
Slowly lower the engine into the engine compartment.
Install the engine with the 4 bolts and 4 nuts.
Remove the 2 bolts and 2 engine hangers.
| 6. INSTALL REAR END PLATE |
Install the rear end plate with the bolt.
| 7. INSTALL PUMP IMPELLER DRIVE PLATE (for Automatic Transmission) |
Clean the bolts and their holes.
![]() |
Using SST, hold the crankshaft pulley.
![]() |
Install the flywheel and ring gear, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.
| *1 | Flywheel and Ring Gear |
| *2 | Pump Impeller Drive Plate |
| *3 | Rear Drive Plate Spacer |
| *a | Engine Side |
| *b | Transmission Side |
![]() |
Install and uniformly tighten and tighten the 8 bolts in several steps in the sequence shown in the illustration.
| 8. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission) |
Clean the bolts and their holes.
Apply adhesive to 2 or 3 threads at the end of each bolt.
![]() |
Using SST, hold the crankshaft pulley.
Install the flywheel to the crankshaft.
![]() |
Install and uniformly tighten and tighten the 8 bolts in the sequence shown in the illustration.
| 9. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission) |
![]() |
Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel.
| 10. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission) |
![]() |
Align the matchmarks on the clutch cover and flywheel.
Tighten the 6 bolts as described below.
Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.
Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.
Lightly move SST up and down, and right and left.
Check that the disc is in the center, and then tighten the bolts.
| 11. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission) |
![]() |
Using a dial indicator with roller instrument, measure the diaphragm spring tip alignment.
![]() |
| 12. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR |
Install the 4 bolts and rear No. 1 engine mounting insulator.
| 13. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission) |
| 14. INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transmission) |
| 15. INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission) |
| 16. CONNECT COOLER COMPRESSOR ASSEMBLY |
Connect the cooler compressor with the 4 bolts.
| 17. CONNECT WIRE HARNESS |
Connect the 4 ECM connectors.
for Automatic Transmission:
Connect the 3 TCM connectors.
Connect the 3 injector driver connectors.
Attach the clamp and connect the wire harness with the 2 nuts.
Connect the ground cable with the bolt.
Connect the 2 engine room junction block connectors.
Connect the engine room junction block wire with the nut.
Install the side engine room relay block cover.
Install the upper relay block cover.
| 18. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Attach the 2 hinges to install the glove compartment door.
| *1 | Hinge |
![]() |
While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
| *1 | Stopper |
| 19. CONNECT UNION TO CONNECTOR TUBE HOSE |
Connect the union to connector tube hose.
| 20. CONNECT FUEL HOSE |
Connect the 2 fuel hoses.
| 21. CONNECT PRESSURE FEED TUBE ASSEMBLY |
Connect the pressure feed tube.
Connect the oil reservoir to pump hose.
| 22. CONNECT HEATER HOSE |
Connect the 2 heater hoses.
| 23. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
| 24. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
| 25. INSTALL STARTER ASSEMBLY |
| 26. INSTALL RADIATOR ASSEMBLY |
| 27. INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY |
Connect the pipe (with the 2 air hoses) and install the bolt.
Tighten the 2 clamps.
Connect the vacuum hose to the gas filter.
Connect the manifold absolute pressure sensor connector.
| 28. INSTALL AIR CLEANER ASSEMBLY |
Connect the air cleaner hose.
Install the cleaner with the 2 bolts.
Tighten the hose clamp.
Connect the connector to the mass air flow meter connector.
| 29. INSTALL BATTERY TRAY |
| 30. INSTALL BATTERY |
| 31. INSTALL BATTERY CLAMP SUB-ASSEMBLY |
Install the battery clamp with the bolt and nut.
| 32. ADD POWER STEERING FLUID |
| 33. ADD TRANSMISSION FLUID (for Automatic Transmission) |
| 34. ADD TRANSMISSION OIL (for Manual Transmission) |
![]() |
| 35. ADD ENGINE OIL |
Add new engine oil.
| Oil Grade | Oil Viscosity (SAE) |
| G-DLD1, API CF-4 or CF (You may also use API CE or CD) | - 5W-30 - 10W-30 - 15W-40 - 20W-50 |
| Item | Specified Condition |
| Drain and refill without oil filter change | 6.6 liters (7.0 US qts, 5.8 Imp. qts) |
| Drain and refill with oil filter change | 6.9 liters (7.3 US qts, 6.1 Imp. qts) |
| Dry fill | 7.4 liters (7.8 US qts, 6.5 Imp. qts) |
Install the oil filler cap.
| 36. INSTALL HOOD SUB-ASSEMBLY |
Install the hood with the 4 bolts.
Connect the washer nozzle hose.
Adjust the hood (Click here).
| 37. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 38. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
| 39. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the B line of the radiator reservoir.
| Item | Specified Condition |
| for Automatic Transmission | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| for Manual Transmission | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the radiator hose inlet and radiator hose outlet several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 40. BLEED AIR FROM POWER STEERING SYSTEM |
Check the fluid level.
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the steering wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine. Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the steering wheel to the left or right full lock position and hold it there for 2 to 3 seconds. Then turn the steering wheel to the opposite full lock position and hold it there for 2 to 3 seconds.
Repeat the step above several times.
Stop the engine.
![]() |
Check for foaming or emulsification. If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.
Check the fluid level.
| 41. INSPECT FOR POWER STEERING FLUID LEVEL |
![]() |
Keep the vehicle level.
With the engine stopped, check the power steering fluid level in the oil reservoir. If necessary, add power steering fluid.
Start the engine and run it at idle.
Turn the steering wheel to the left or right full lock position, and then turn the wheel to the opposite full lock position. Repeat this several times to raise fluid temperature.
![]() |
Check for foaming or emulsification. If foaming or emulsification is identified, bleed air from the power steering system.
![]() |
With the engine idling, measure the fluid level in the oil reservoir.
Stop the engine.
Wait a few minutes and remeasure the fluid level in the oil reservoir.
Check the fluid level.
| 42. PERFORM REGISTRATION |
Perform registration of the injector compensation codes .
Perform pilot quantity learning .
| 43. INSPECT FOR COOLANT LEAK |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 44. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
| 45. INSPECT FOR EXHAUST GAS LEAK |
| 46. INSPECT FOR FUEL LEAK |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and turn the intelligent tester main switch on.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.
| 47. CHECK ENGINE IDLE SPEED AND MAXIMUM SPEED |
Connect the intelligent tester to the DLC3.
![]() |
If a tester is not available, connect the tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.
| *a | Front view of DLC3 |
Inspect the idle speed.
Start the engine and measure the idle speed.
Inspect the maximum speed.
Start the engine.
Fully depress the accelerator pedal.
Measure the maximum speed.
If the tester probe of a tachometer is connected to the DLC3, disconnect the tester probe together with SST from terminal 9 of the DLC3.
Disconnect the intelligent tester from the DLC3.
| 48. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.
| 49. INSTALL NO. 2 ENGINE UNDER COVER |
| 50. INSTALL NO. 1 ENGINE UNDER COVER |