DTC P13A1 Fuel Pressure Sensor Circuit Low #1(Sub CPU) |
DTC P13A2 Fuel Pressure Sensor Circuit High #1(Sub CPU) |
DTC P13A3 Fuel Pressure Sensor Circuit Range/Performance #1 |
DTC P13A6 Fuel Pressure Sensor Circuit Low #2(Sub CPU) |
DTC P13A7 Fuel Pressure Sensor Circuit High #2(Sub CPU) |
DTC P13A8 Fuel Pressure Sensor Circuit Range/Performance #2 |
DTC P13AB Fuel Pressure Sensor Circuit Low #3(Sub CPU) |
DTC P13AC Fuel Pressure Sensor Circuit High #3(Sub CPU) |
DTC P13AD Fuel Pressure Sensor Circuit Range/Performance #3 |
DTC P13B1 Fuel Pressure Sensor Circuit Low #4(Sub CPU) |
DTC P13B2 Fuel Pressure Sensor Circuit High #4(Sub CPU) |
DTC P13B3 Fuel Pressure Sensor Circuit Range/Performance #4 |
DTC P13E1 Fuel Pressure Sensor Circuit Low #1(Main CPU) |
DTC P13E2 Fuel Pressure Sensor Circuit High #1(Main CPU) |
DTC P13E6 Fuel Pressure Sensor Circuit Low #4(Main CPU) |
DTC P13E7 Fuel Pressure Sensor Circuit High #4(Main CPU) |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 1 second or more | Sub CPU Side: The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 1 second or more | Sub CPU Side: The output voltage of the fuel pressure sensor is 4.84 V or higher for 0.5 seconds or more. (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 8 seconds or more | Main CPU Side: The fuel pressure sensor output voltage of injector #1 and/or #4 is below 0.5 V for 3 seconds or more. (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 8 seconds or more | Main CPU Side: The fuel pressure sensor output voltage of injector #1 and/or #4 is higher than 4.85 V for 3 seconds or more. (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds | The output of the fuel pressure sensor differs by 33 MPa or more compared to other cylinders for 0.5 seconds or more. (1 trip detection logic) |
|
| DTC No. | Data List |
| P13A1 P13A2 P13A6 P13A7 P13AB P13AC P13B1 P13B2 |
|
| P13E1 P13E2 P13E6 P13E7 | |
| P13A3 P13A8 P13AD P13B3 |

| 1.CHECK FOR ANY OTHER DTCS OUTPUT |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| "Fuel pressure sensor circuit DTC" and "Injector Internal EEPROM Malfunction circuit DTC" are output*1 | A |
| Except above | B |
|
| ||||
| B | |
| 2.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE) |
Disconnect the fuel pressure sensor connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected (ECM) |
| Tester Connection | Switch Condition | Specified Condition |
| E29-18 (VIJ1) - E29-6 (EIJ1) | Ignition switch ON | 4.5 to 5.5 V |
| E29-17 (VIJ2) - E29-5 (EIJ2) | Ignition switch ON | 4.5 to 5.5 V |
| E29-16 (VIJ3) - E29-4 (EIJ3) | Ignition switch ON | 4.5 to 5.5 V |
| E29-15 (VIJ4) - E29-3 (EIJ4) | Ignition switch ON | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM) |
Disconnect the injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F31-2 (VIJ1) - E29-18 (VIJ1) | Always | Below 1 Ω |
| F31-4 (PIJ1) - E29-12 (PIJ1) | Always | Below 1 Ω |
| F31-1 (EIJ1) - E29-6 (EIJ1) | Always | Below 1 Ω |
| F32-2 (VIJ2) - E29-17 (VIJ2) | Always | Below 1 Ω |
| F32-4 (PIJ2) - E29-11 (PIJ2) | Always | Below 1 Ω |
| F32-1 (EIJ2) - E29-5 (EIJ2) | Always | Below 1 Ω |
| F33-2 (VIJ3) - E29-16 (VIJ3) | Always | Below 1 Ω |
| F33-4 (PIJ3) - E29-10 (PIJ3) | Always | Below 1 Ω |
| F33-1 (EIJ3) - E29-4 (EIJ3) | Always | Below 1 Ω |
| F34-2 (VIJ4) - E29-15 (VIJ4) | Always | Below 1 Ω |
| F34-4 (PIJ4) - E29-9 (PIJ4) | Always | Below 1 Ω |
| F34-1 (EIJ4) - E29-3 (EIJ4) | Always | Below 1 Ω |
| F31-4 (PIJ1) or E29-12 (PIJ1) - Body ground | Always | 10 kΩ or higher |
| F31-1 (EIJ1) or E29-6 (EIJ1) - Body ground | Always | 10 kΩ or higher |
| F32-4 (PIJ2) or E29-11 (PIJ2) - Body ground | Always | 10 kΩ or higher |
| F32-1 (EIJ2) or E29-5 (EIJ2) - Body ground | Always | 10 kΩ or higher |
| F33-4 (PIJ3) or E29-10 (PIJ3) - Body ground | Always | 10 kΩ or higher |
| F33-1 (EIJ3) or E29-4 (EIJ3) - Body ground | Always | 10 kΩ or higher |
| F34-4 (PIJ4) or E29-9 (PIJ4) - Body ground | Always | 10 kΩ or higher |
| F34-1 (EIJ4) or E29-3 (EIJ4) - Body ground | Always | 10 kΩ or higher |
Reconnect the injector assembly connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER) |
Replace the injector assembly of the cylinder relevant to the DTC (Click here).
| NEXT | |
| 5.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
|
| ||||
| 6.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 7.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 8 seconds or more.
Start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||