DTC P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low |
DTC P2565 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 1 second | VNA voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 1 second | VNA voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic). |
|

| 1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2564 AND P2565) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P2564 and/or P2565 is output | A |
| P2564 and/or P2565 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR) |
Disconnect the nozzle vane position sensor connector.
Disconnect the ECM.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T11-1 (VTA1) - E30-11 (VNA) | Always | Below 1 Ω |
| T11-2 (VNE2) - E30-5 (VNE2) | Always | Below 1 Ω |
| T11-3 (VNVC) - E30-17 (VNVC) | Always | Below 1 Ω |
| T11-1 (VTA1) or E30-11 (VNA) - Body ground | Always | 10 kΩ or higher |
| T11-3 (VNVC) or E30-17 (VNVC) - Body ground | Always | 10 kΩ or higher |
Reconnect the nozzle vane position sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VNVC VOLTAGE) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E30-17 (VNVC) - E30-5 (VNE2) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Component with harness connected (ECM) |
|
| ||||
| NG | |
| 4.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 5.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR) |
Replace the turbocharger sub-assembly (Click here).
|
| ||||
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and wait for 10 seconds or more.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input DTC P2564 and/or P2565.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.
| NEXT | ||
| ||