CAN COMMUNICATION SYSTEM (w/ VSC) > Short to B+ in CAN Bus Line |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ. |
|

| 1.PRECAUTION |
| NEXT | |
| 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
| NEXT | |
| 3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE) |
![]() |
Disconnect the J52 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D3-6 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| D3-14 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 4.CONNECT CONNECTOR |
Reconnect the J52 No. 3 junction connector.
| NEXT | |
| 5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE) |
![]() |
Disconnect the J64 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D3-6 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| D3-14 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J64-13 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J64-7 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J64-12 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J64-6 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 8.CONNECT CONNECTOR |
Reconnect the J64 No. 1 junction connector.
| NEXT | |
| 9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU) |
![]() |
Disconnect the S25 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S25-25 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| S25-14 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to Brake Actuator Assembly [Skid Control ECU]) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 10.CONNECT CONNECTOR |
Reconnect the J64 No. 1 junction connector.
| NEXT | |
| 11.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM) |
Disconnect the E13*1 or E5*2 ECM connector.

| *A | for 1GR-FE | *B | for 1KD-FTV |
| *a | Front view of wire harness connector (to ECM) | *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E13-33 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E13-34 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
| E5-24 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E5-23 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Result | Proceed to |
| OK (for 1GR-FE) | A |
| OK (for 1KD-FTV [w/ Glow Plug Controller]) | B |
| OK (for 1KD-FTV [w/o Glow Plug Controller]) | C |
| NG | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 12.CONNECT CONNECTOR |
Reconnect the J64 No. 1 junction connector.
| NEXT | |
| 13.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR) |
![]() |
Disconnect the J65 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J65-5 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J65-16 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D3-6 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| D3-14 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J65-7 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J65-18 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 16.CONNECT CONNECTOR |
Reconnect the J65 No. 2 junction connector.
| NEXT | |
| 17.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY) |
![]() |
Disconnect the Y1 yaw rate sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Y1-3 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Y1-2 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to Yaw Rate Sensor Assembly) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 18.CONNECT CONNECTOR |
Reconnect the J65 No. 2 junction connector.
| NEXT | |
| 19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Disconnect the J53 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J53-2 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J53-1 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - STEERING ANGLE SENSOR) |
![]() |
Disconnect the J63 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J63-2 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J63-1 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 21.CONNECT CONNECTOR |
Reconnect the J53 and J63 No. 3 junction connectors.
| NEXT | |
| 22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR) |
![]() |
Disconnect the S31 spiral cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S31-4 (CANH) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| S31-3 (CANL) - D3-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to Spiral Cable Sub-assembly [Steering Angle Sensor]) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||