Home › Drivetrain › R151 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY › 2015.11–2016.07
RM33K0E _52 Drivetrain _043528 R151 MANUAL TRANSMISSION / TRANSAXLE _0212624 MANUAL TRANSMISSION ASSEMBLY A

R151 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.


PROCEDURE

Hide 1.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C325405N01
1.583,0.104 1.938,0.365 0.354,0.26 10 false (A) 3.083,0.313 3.385,0.573 0.302,0.26 10 false (B)

Install the 2 wire harness clamp brackets to the manual transmission unit sub-assembly with the 2 bolts.

Torque:
bolt A : 64 N*m (653 kgf*cm, 47 ft.*lbf)
bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33019C 2.INSTALL TRANSMISSION BREATHER SUB-ASSEMBLY

a.
C325673

Connect the 2 clamps and install the transmission breather sub-assembly.


Hide 33030 3.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY

CAUTION:

The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.


a.

Make sure that the knock pins are not loose, bent, damaged or scratched.


b.

Operate the transmission jack and install the manual transmission unit assembly to the vehicle.

CAUTION:

Do not raise the manual transmission unit assembly more than necessary. If the manual transmission unit assembly is raised excessively, the vehicle may also be lifted up.


NOTICE:

Make sure that the manual transmission unit assembly is clear of all wiring and hoses.



c.

Align the input shaft with the clutch disc and install the manual transmission unit assembly to the engine.


d.
C338127C01
2.771,0.896 2.823,0.688 2.823,0.688 2.948,0.688 false 3.01,0.615 3.323,0.771 0.313,0.156 10 false *1
*1 Transmission Breather Bracket


Install the transmission breather bracket and 7 bolts.

Torque:
for bolt a : 71.5 N*m (729 kgf*cm, 53 ft.*lbf)
for bolt b : 37.2 N*m (379 kgf*cm, 27 ft.*lbf)


Hide 12371A 5.INSTALL REAR ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 51204 6.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

Torque:
57 N*m (581 kgf*cm, 42 ft.*lbf)


b.

Connect the No. 3 frame crossmember sub-assembly to the rear engine mounting insulator.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 8.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

a.

Install the clutch release cylinder assembly with the 2 bolts.

Torque:
11.7 N*m (119 kgf*cm, 9 ft.*lbf)


Hide 9.CONNECT WIRE HARNESS

a.
C325676

Connect the 2 clamps and connector.


b.
C325671

Connect the ground cable with the bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 17410 10.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 11.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 51442 12.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51410 13.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 33530F 15.INSTALL FLOOR SHIFT LEVER ASSEMBLY

a.
C333520C01
1.813,1.719 1.948,1.896 0.135,0.177 10 false -
V100135

MP grease


Apply MP grease to the tip of the shift lever.


b.
C329000C02
1.958,0.688 2.323,0.333 2.323,0.333 2.479,0.333 true 1.146,0.24 1.354,0.458 0.208,0.219 10 false *a 1.75,2.906 1.938,3.083 0.188,0.177 10 false *b 1.844,4.271 2.021,4.448 0.177,0.177 10 false *c 2.531,0.26 2.771,0.5 0.24,0.24 10 false *1
*1 Shift Lever Cap
*a Press Down
*b Clockwise
*c Lock


Cover the shift lever cap with a cloth.


c.

While pressing down on the shift lever cap, turn it clockwise to install the shift lever assembly.


d.

Attach the shift lever cap boot.


Hide 58280A 16.INSTALL SHIFT LEVER BOOT ASSEMBLY

a.

Install the shift lever boot assembly with the 6 screws and 4 clips.


b.

Install the shift lever cover.


Hide 58810J 17.INSTALL CONSOLE BOX ASSEMBLY

Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION