Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM33K0E _51 Engine / Hybrid System _043570 2TR-FE ENGINE MECHANICAL _0225067 ENGINE ASSEMBLY A

2TR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12361 2.INSTALL FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.

Install the 2 front engine mounting insulators to the 2 front engine mounting brackets with the 2 nuts.

Torque:
58 N*m (591 kgf*cm, 43 ft.*lbf)


Hide 12391 3.INSTALL FRONT ENGINE MOUNTING HEAT INSULATOR RH

a.

Install the front engine mounting heat insulator RH to the front engine mounting insulator with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 82121 4.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 11000 5.REMOVE ENGINE FROM ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Attach the engine sling device and hang the engine assembly with the chain block.


b.

Remove the engine assembly from the engine stand.


Hide 11000 6.INSTALL ENGINE ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Slowly lower the engine assembly into the engine compartment.


b.

Install the engine assembly to the body with the 4 bolts and 4 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
·

Make sure to tighten the side with the nut.

·

When installing a bolt with a claw (stopper), make sure that the claw (stopper) does not damage the body of the vehicle.




c.

Remove the 2 bolts and 2 engine hangers.


Hide 11355 7.INSTALL REAR END PLATE

a.

Install the rear end plate to the cylinder block with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the No. 1 water by-pass pipe to the rear end plate with the bolt.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 32101 8.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

Hide 13405 9.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

Hide 31250 10.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 31210 11.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31210 12.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 14.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 41110F 15.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

Hide 44250 16.INSTALL POWER STEERING LINK ASSEMBLY (for 4WD)

Hide 45219 17.CONNECT STEERING SLIDING YOKE (for 4WD)

Hide 43410D 18.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING (for 4WD)

Hide 43420 19.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)

Hide 43410 20.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:

Use the same procedure described for the LH side.


Hide 89543 21.CONNECT FRONT SPEED SENSOR LH (for 4WD)

Hide 48069 22.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH (for 4WD)

Hide 23.CONNECT TIE ROD END SUB-ASSEMBLY LH (for 4WD)

Hide 43502H 24.INSTALL FRONT AXLE SHAFT NUT (for 4WD)

Hide 43514C 25.INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)

Hide 37100 26.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for Pre-Runner)

Hide 37100 27.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)

Hide 17410 31.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 32.CONNECT ENGINE WIRE

a.

Connect the sensor bracket to the right side of the frame with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


b.

Connect the air fuel ratio sensor connector.


c.

Connect the wire clamp to the front engine mounting bracket LH with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


d.

Attach the clamp.


e.

Connect the 2 connectors to the engine room relay block.


f.

Connect the engine wire to the engine room relay block with the nut.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


g.

Attach the 2 claws and install the No. 1 relay block cover side to the engine room relay block.


h.

Attach the 3 claws and install the No. 1 relay block cover upper to the engine room relay block.


i.
A348578N01
1.521,1.135 1.802,1.333 0.281,0.198 10 true 45° 1.521,1.531 1.802,1.729 0.281,0.198 10 true 45°

Attach the clamp and install the No. 2 engine wire with the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

HINT:

Position the No. 2 engine wire as shown in the illustration.



j.

Attach the 2 clamps and connect the No. 2 engine wire with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


k.

Install the battery tray.


l.

Install the battery.


m.

Install the battery hold down clamp with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


n.
A348574N01
1.708,0.01 1.917,0.198 0.208,0.188 10 true 8° 1.417,0.01 1.625,0.198 0.208,0.188 10 true 8°

Tighten the nut and install the positive (+) battery terminal.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

Position the positive (+) battery terminal as shown in the illustration.



o.

Connect the engine room main wire to the positive (+) battery terminal with the nut.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


p.

Connect the connector to the engine room main wire.


q.
A359072N01
1.552,0.063 1.854,0.26 0.302,0.198 10 true 45° 2.219,0.073 2.521,0.271 0.302,0.198 10 true 45°

for LHD:

i.

Push the engine wire through the dash panel into the cabin.

HINT:

The wire should be within the range shown in the illustration.




r.
A348591N01
2.729,0.073 3.021,0.25 0.292,0.177 10 true 45° 2.177,0.073 2.469,0.25 0.292,0.177 10 true 45°

for RHD:

i.

Push the engine wire through the dash panel into the cabin.

HINT:

The wire should be within the range shown in the illustration.




s.

w/ Secondary Air Injection System:

i.

Connect the engine wire to the air injection control bracket with the bolt.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


ii.

Attach the clamp.


iii.

Connect the air injection control driver connector.



t.

w/o Secondary Air Injection System:

i.

Connect the engine wire to the air injection control bracket with the bolt.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)



u.

Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.


Hide 55550 34.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 23271H 35.CONNECT NO. 1 FUEL HOSE

Hide 23273C 36.CONNECT NO. 2 FUEL HOSE

Hide 17344 37.CONNECT NO. 4 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)

Hide 44774 38.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose to the intake manifold, and slide the clamp to secure the hose.


Hide 39.CONNECT PURGE LINE HOSE

a.

Connect the purge line hose to the purge VSV, and slide the clamp to secure the hose.


Hide 88320 41.CONNECT COOLER COMPRESSOR ASSEMBLY

Hide 11452 42.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring and the engine oil level dipstick guide with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 15301 43.INSTALL ENGINE OIL LEVEL DIPSTICK

Hide 44320 44.CONNECT VANE PUMP ASSEMBLY

a.

Connect the vane pump assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the power steering oil pressure switch connector.


Hide 45.CONNECT HEATER HOSE

a.

Connect the heater water outlet hose to the heater radiator unit sub-assembly, and slide the clamp to secure the hose.


b.

Connect the heater water inlet hose to the heater radiator unit sub-assembly, and slide the clamp to secure the hose.


Hide 16400 46.INSTALL RADIATOR ASSEMBLY

Hide 32941 47.CONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 32942 48.CONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 16711 49.INSTALL FAN SHROUD

Hide 16470 50.INSTALL RADIATOR RESERVOIR

Hide 17621A 51.CONNECT AIR PUMP INLET (w/ Secondary Air Injection System)

Hide 16572 52.INSTALL RADIATOR HOSE OUTLET

Hide 16571 53.INSTALL RADIATOR HOSE INLET

Hide 16593 54.INSTALL NO. 1 RADIATOR AIR GUIDE

Hide 53294C 55.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 53293C 56.INSTALL RADIATOR SIDE DEFLECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 17861 57.INSTALL INTAKE AIR CONNECTOR

Hide 17701 58.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 3 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Attach the 3 wire harness clamps.


Hide 17801 59.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner cap sub-assembly.


Hide 17705 60.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE

a.

Install the air cleaner cap sub-assembly with air cleaner hose and tighten the hose clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Attach the 4 clamps.


c.

Connect the intake mass air flow meter connector and attach the 2 wire harness clamps.


Hide 53301 61.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the washer nozzle hose to the hood sub-assembly.


c.

Adjust the hood sub-assembly.

Click hereVehicle Exterior>DOOR / HATCH>HOOD>ADJUSTMENT


Hide 62.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 33820B 65.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 70.ADD DIFFERENTIAL OIL (for 4WD)

Hide 22030 78.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 53882F 79.INSTALL FRONT FENDER SEAL LH

a.

Install the front fender seal LH with 6 new clips.


Hide 53882F 80.INSTALL FRONT FENDER SEAL RH

a.

Install the front fender seal RH with 6 new clips.


Hide 53737B 81.INSTALL FRONT UPPER FENDER APRON SEAL LH

a.

Install the front upper fender apron seal LH with 6 new clips.


Hide 53736 82.INSTALL FRONT UPPER FENDER APRON SEAL RH

a.

w/ Secondary Air Injection System:

i.

Install the front upper fender apron seal RH with 5 new clips.



b.

w/o Secondary Air Injection System:

i.

Install the front upper fender apron seal RH with 6 new clips.



Hide 51407A 83.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Cover)

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51442 84.INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51410 85.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Torque:
for M6 bolt : 11.5 N*m (117 kgf*cm, 8 ft.*lbf)
for M8 bolt : 28 N*m (286 kgf*cm, 21 ft.*lbf)